Systems & Products 

Every Alchatek system and

product, organized by the

problem it solves

Soil stabilization, concrete leveling and stabilization, leak sealing, and seawall repair. Four system families, plus the sealants, pumps, equipment, and accessories that complete the work.

ISO 9001-certified manufacturing

Designed and manufactured by Alchatek

Facilities in the US, Europe & Australia

Packaging

How our products ship

Packaging formats across the product line, from cartridge to tote set. Single-component products ship in individual containers; two-component products ship as paired sets. A tote is also called an IBC. Available formats for each product are listed on its product page.

Spetec HighFoamer INJECTR cartridges in a retail display box, showing the cartridge packaging format Cartridge INJECTR Series
Two foil-wrapped sausage packs of Alchatek sealant in front of shipping cartons 20 oz Sausage Slab Seal
Spetec HighFoamer in a pail, one of the packaging formats for Alchatek products 5-Gallon Pail
Spetec HighFoamer in a 55-gallon drum, one of the packaging formats for Alchatek products 55-Gallon Drum
AP Fill 700 in a 275-gallon IBC tote, one of the packaging formats for Alchatek products 25-Gallon Tote (IBC)
Red and blue 55-gallon drums forming a two-component AP 400 Series and AP Lift drum set Drum Set Paired drums two-component products
Two IBC totes of two-component Alchatek polyurethane foam, Part A and Part B, shown as a tote set Tote Set Paired totes for two-component products

Stabilize

Geotechnical Soil

Stabilization Systems

Use when the ground beneath a structure is moving, voiding, or failing to carry load, and the fix has to happen in the soil itself. These are single-component permeation systems, and every one of them can be used for Deep Lock®, Alchatek’s deep soil stabilization approach.

How these are selected: AP Soil 600 and AP Fill 700 belong in conversations involving loose granular soils, matrix improvement, permeation logic (the resin travels into the pore space between soil grains instead of forming a mass), excavation assist, solar pile stabilization, launch pit support, and other scenarios where soil behavior drives the selection process. AP Lift systems are typically evaluated where stabilization and potential lift behavior are both part of the objective.

Every two-component product, AP Fill 420 and the AP Lift series (430, 440, 475, 460), also performs geotechnical soil stabilization when used for Deep Lock®; each is detailed under Concrete Leveling and Stabilization below.

Seal water out

Spetec Leak

Seal Systems

Use when water is coming through concrete: cracks, joints, penetrations, and active leaks that need flexible sealing or curtain grouting. Injection resin fills the full depth of the crack or joint, through the structure, not just the face.

Waterfront

Seawall & Waterfront

Stabilization Systems

Use when soil is washing out behind a seawall or bulkhead and the fix has to restore subsurface continuity, not just patch the face.

The injection resins in this family are part of the Geotechnical Soil Stabilization line; they appear in both families because seawall and waterfront work is where the selection and injection strategy differ.

Seal the face of the joint

Joint & Crack

Sealants

Use when slab joints and cracks need a flexible seal at the surface, after the structural work is done. A joint sealant closes the face of the crack or joint; it does not fill it through the structure. If water is moving through the crack or joint, see Spetec Leak Seal Systems instead.

Apply

Pumps

& Equipment

The injection pumps and application equipment the materials are designed to run through.

Complete the job

Access

Injection ports, packers, fittings, and the other components each system runs with, organized by the family they serve. Each opens its own page.

System-level positioning

Deep Lock® is a
deep soil injection
stabilization system

Deep Lock® is Alchatek’s deep soil stabilization system approach. It is designed to engage weak strata within the active load zone through engineered injection strategy and product selection, with stabilization as the primary objective.

Why it is a system,

not a product

Deep Lock® belongs in a system conversation, not a generic lifting conversation. Every product in the Geotechnical Soil Stabilization and Concrete Leveling and Stabilization families can be used for it; which one applies depends on injection depth, soil behavior, and the objective.

Technicians injecting foam through a grid of probes in a residential street to stabilize soil beneath the pavement

Documentation

Where the documentation lives

Two places, two different jobs. Each product page carries the files for that product — technical data sheet, safety data sheet, installation details, and the guidance written specifically for it. Engineering Resources › Downloads holds the complete library across every product and system, which is what you want when you are assembling a submittal package or comparing files side by side.

Still narrowing the method? Knowledge Center: how these methods differ.

Project-specific family questions: Technical Services.

Frequently Asked Questions

Common questions
about systems, products,
and documentation

Choosing the right system family

Start with the condition and the repair objective. If the issue is slab elevation and shallow support, concrete leveling and stabilization may belong. If broader or deeper support reliability is the issue, soil stabilization may belong. If water entry is the problem, leak-seal systems may belong.

No. Product-family selection should follow condition and method logic. Choosing families too early increases the risk of comparing products before the failure mechanism is clear.

A system family groups products around a common repair logic or performance objective. Individual products are selected only after the family, method fit, and application constraints are better defined.

Yes. The AP Lift series is detailed under Concrete Leveling and Stabilization and cross-referenced under Geotechnical Soil Stabilization, because the same resin can lift a slab or stabilize the ground beneath it depending on injection depth and strategy.

Yes. Some projects involve both support and water-control issues, or move from family orientation into paired method logic. When more than one family appears relevant, use the solution pages and Technical Services to narrow the right sequence.

Soil, support, and Deep Lock®

Deep Lock® is Alchatek’s deep soil stabilization system approach for engaging weak strata within the active load zone where stabilization, not just surface lift, is the primary objective.

AP Lift systems are considered where controlled reaction behavior and potential lift are part of the objective. Permeation and matrix-binding products are considered when pore-space penetration and soil binding are the primary goals.

They are graded by application intensity. AP Lift 430 is for residential and light commercial work. AP Lift 440 is for DOT and highway work. AP Lift 475 is for heavy, intensive applications. AP Lift 460 is the heaviest in the series.

AP Soil 600 is a permeation grout with minimal expansion. AP Fill 700 is a permeation grout that also expands, adding water cut-off and void filling. Choose based on whether expansion helps or hurts the objective.

Every product in the Geotechnical Soil Stabilization and Concrete Leveling and Stabilization families can be used for Deep Lock®: AP Soil 600, AP Fill 700, AP Fill 720, AP Fill 420, and the AP Lift series (430, 440, 475, 460). Deep Lock® is a deep soil stabilization approach, not a single product.

Leak sealing and water control

Spetec Leak Seal Systems cover the leak-seal and water-control family used for active leakage, seepage, joints, cracks, penetrations, and other water-entry conditions where flexible sealing or water-management logic is needed.

The products rated for gushing leaks are Spetec GT380, Spetec AG200, Spetec H200, Spetec HighFoamer, and Spetec Boom! Seal. Final selection depends on flow rate, crack width, and substrate condition.

Hydrophobic resins react with water and expand, which helps drive water back and seal active flow. Hydrophilic resins absorb water and stay flexible, which helps accommodate movement in joints that stay damp.

Documentation, escalation, and buying

Move into Engineering Resources when the next question is about specifications, details, technical data, submittals, or other formal files rather than family-level orientation.

Move into Engineering Resources for technical files, and into Technical Services when the family question is still project-specific or high-risk.

Request technical support when the condition is unclear, multiple families could fit, documentation matters, or the project carries enough risk that product-family orientation alone is not enough.

Compare families by condition, performance objective, access constraints, and documentation needs first. Avoid comparing products before the family logic is clear.

The Spetec leak sealing and waterproofing line is sold through distribution. Geotechnical products are sold direct. Select soil stabilization and seawall products can move through distribution for the right partner.

Next step

Alchatek designs the systems and manufactures the materials and equipment behind them

When you know the product, the documentation is in Engineering Resources. When the project still has open questions, Technical Services can work it through with you.