Soil Stabilization & Settlement Control · Permeation Grout
AP Soil 600 Polyurethane Permeation Grout
A single-component permeation grout at 38 cP, thin enough to travel between sand grains and bind loose soil where it sits, instead of displacing it.
NSF/ANSI/CAN 61 Certified · Certified for contact with drinking water
Permeation grouting
Extra low viscosity
No catalyst required
Sinkhole remediation
On this page:
What it is
A permeation grout thin enough to travel between sand grains
AP Soil 600 is a single-component, moisture-activated, hydrophobic polyurethane permeation grout used to encapsulate and strengthen loose sand and soil, and for sinkhole remediation. Its published pre-activated mix viscosity is 38 cP, the lowest in the geotechnical line, which is what lets it move through the pore spaces in sandy ground rather than fracturing it.
It requires no catalyst. The resin cures on the moisture already in the ground, in about 3 hours on its own. Catalyst is optional and is used only to pull that cure time in, down to about 25 minutes at the top of the published range.
Where it is used
What AP Soil 600 is used for
AP Soil 600 sits in the Soil Stabilization & Settlement Control solution family.
Permeation grouting
Stabilizing loose sand and soil
Stabilizing soil around concrete structures
Sinkhole remediation
How it works
How AP Soil 600 strengthens ground without replacing it
AP Soil 600 is injected into sandy ground, where it travels through the pore spaces between the grains, reacts with the moisture already present, and cures to bind the grains into a single mass. The soil is not removed or displaced. It is encapsulated, which is why the published strength figures describe the grouted sand rather than the resin alone.
Viscosity is the whole mechanism. At 38 cP the resin behaves closer to a liquid that soaks in than a foam that pushes out, so it fills between grains instead of fracturing the ground and forming lenses. Cure time is the other variable a crew controls, from about 3 hours with no catalyst down to about 25 minutes at 3 percent, which sets how far the resin travels before it sets.
Technical specifications
Published properties
Resin and grouted soil
Property | Value | Method |
|---|---|---|
Pre-activated mix viscosity | 38 cP (38 mPa·s) | TDS |
Compressive strength, permeated in sand | 1,300 psi, or 187,000 psf (8,960 kPa) | ASTM D2166 |
Shear strength, permeated in sand | 665 psi, or 95,800 psf (4,590 kPa) | ASTM D2166 |
Shrinkage | Negligible | ASTM D1042 / D756 |
Cure time by catalyst dosage
Catalyst | Cure time |
|---|---|
None | 3 hours |
0.5% | 2 hours 30 minutes |
1.0% | 2 hours |
1.5% | 1 hour 20 minutes |
2.0% | 55 minutes |
2.5% | 30 minutes |
3.0% | 25 minutes |
Handling & certification
Property | Value | Method / Note |
|---|---|---|
Composition | Single component, moisture activated, hydrophobic; no catalyst required; phthalate free | TDS / product page |
Storage | 50–80°F (10–26°C) | TDS |
Shelf life | 24 months, unopened, within storage range | TDS |
Packaging | 5-gallon pail, 50-gallon drum, and 250-gallon tote | Product page |
Certification | NSF/ANSI/CAN 61. Certified for contact with drinking water. Read the certificate for the conditions of the listing. | TDS Rev. 1/20/2026 and certified product listing |
Strength figures describe sand permeated with the resin, not the cured resin alone. Catalyst dosage is by volume; confirm the dose for your container size against the current data sheet before mixing. Source: AP Soil 600 Technical Data Sheet, Rev. 1/20/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.
Downloads
Data sheets, specifications, and certificates
Technical Data Sheet (TDS)
Published properties · PDF
Safety Data Sheet (SDS)
Handling & safety · PDF
Specification, CSI 31 32 00
Soil stabilization and ground modification · PDF
NSF/ANSI/CAN 61 Certificate
Certified product listing · PDF
Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.
Compatible equipment & accessories
What you need to inject AP Soil 600
Single-component airless injection pump, recommended for AP Soil 600. View pumps
Injection probes, for placing the resin at depth in the soil profile. View accessories
Alchatek Cat 600, optional. AP Soil 600 needs no catalyst to cure; this is used only to shorten cure time. View catalyst
Alchatek Pump Flush, reusable, biodegradable pump flush for shutdown. View flush
Alchatek Soak 130, cured-polyurethane cleaning solvent. View solvent
Related articles & guides
Learn the method behind the product
Polyurethane Soil Stabilization Explained
Method explainer
Polyurethane Soil Stabilization Case Studies
Project evidence
Stabilizing Sandy Soils with AP Soil 600
Field walk-through
Frequently Asked Questions
Permeation grouting. It is used to stabilize loose sand and soil around concrete structures, and for sinkhole remediation. The resin encapsulates and strengthens the soil rather than replacing it.
Viscosity, and what it is trying to do. At 38 cP pre-activated mix viscosity this is the thinnest resin in the geotechnical line, thin enough to travel through the pore spaces between sand grains and bind them. A thicker, high-expansion resin fills a void or fractures the ground instead of permeating it.
No. It cures on its own with the moisture in the ground, in about 3 hours with no catalyst. Catalyst is optional and is used to shorten that: the published table runs from 3 hours at zero catalyst down to 25 minutes at 3 percent.
About 3 hours uncatalyzed. With catalyst the published cure times are 2 hours 30 minutes at 0.5 percent, 2 hours at 1 percent, 1 hour 20 minutes at 1.5 percent, 55 minutes at 2 percent, 30 minutes at 2.5 percent, and 25 minutes at 3 percent.
Published compressive strength permeated in sand is 1,300 psi, or 187,000 psf, and published shear strength permeated in sand is 665 psi, or 95,800 psf, both by ASTM D2166. Both figures describe the grouted sand mass, not the resin on its own.
AP Soil 600 is certified to NSF/ANSI/CAN 61, which covers contact with drinking water. Read the certificate for the conditions of the listing, and confirm the certification is current before specifying.
Yes. Alchatek publishes a CSI Section 31 32 00 specification, Soil Stabilization and Ground Modification, written around AP Soil 600 and its accessories. It is in the downloads on this page.
5-gallon pails, 50-gallon drums, and 250-gallon totes.
A single-component airless injection pump is recommended, along with injection probes for placing the resin at depth, Alchatek Pump Flush for shutdown, and Alchatek Soak 130 for cleaning cured polyurethane off equipment. Catalyst is optional and used only to shorten cure time.
Unopened containers have a 24 month shelf life when stored between 50 and 80 degrees F.
Proof & Verification
APSOIL600-PB-01
Stabilizing a 5.75 Million Pound Space Launch System
Loose sand under a structure, or a sinkhole that needs the ground bound rather than filled? Talk the soil through before the probes go in.
For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.