Concrete Leveling & Stabilization · Structural Foam
AP Lift 430 Fast Structural Polyurethane Foam
The same 3 lb foam as AP Lift 430, tack free in 11 seconds instead of 17. On a sidewalk or a patio, that speed is the whole point: the foam turns to structure under the port before it can travel across a narrow slab and lift the end that never settled.
ISO 9001 Certified · Facility-wide quality management certification.
Sidewalks & patios
Narrow & lightweight slabs
Slab lifting & leveling
Soil densification
On this page:
What it is
A super-fast-setting structural foam for sidewalks, patios, and narrow slabs
AP Lift 430 Fast is a two component, super-fast-setting structural polyurethane foam used to raise settled concrete slabs, fill the voids beneath them, and densify the weak ground that let them settle. It reaches tack free in 11 seconds, and on a narrow slab that speed is the reason to specify it. It is a 3 lb foam, meaning a nominal cured density of 3 pounds per cubic foot, the grade contractors specify for residential and light commercial slab work. The two sides are heated, metered, and mixed at the gun, then injected through small ports drilled in the slab.
It is also hydro insensitive, which means water in the ground does not stop the reaction.
Where it is used
What AP Lift 430 Fast is used for
It is most often specified on sidewalks, walkways, patios, and other narrow or lightweight slabs, where a slower foam has room to run. Crews use it well beyond those, but that is the job it was built for. AP Lift 430 Fast sits in the Concrete Leveling and Stabilization solution family, and is also used for soil stabilization work where the ground itself is the problem.
The data sheet lists these uses:
Lifting concrete slabs
Stabilizing soil
Filling voids
Filling abandoned pipes and mine shafts
Not sure whether the slab or the ground is the real problem? Start with settled concrete slabs if the concrete has dropped but the ground below is still solid, or soil instability beneath structures if the ground itself is weak or still moving.
How it works
Why speed matters most on a narrow slab
Small ports are drilled through the slab, the two components are heated and mixed at the gun, and the foam is injected beneath the concrete, where it expands in seconds, fills the void, compresses the surrounding soil, and then lifts the slab. AP Lift 430 Fast runs that sequence on a much shorter clock: tack free in 11 seconds against 17 for the standard product, full rise in 18 seconds against 23.
On a wide slab there is room for the foam to work. On a sidewalk four feet across there is not. Injected foam spreads in every direction, and a narrow slab is narrow enough that it can reach the far edge while it is still liquid. When that happens the lift lands under the section that never settled, and the trip hazard you were called out to fix is worse than when you arrived.
A super fast reaction closes that window. The foam turns to structure under the port instead of at the far edge, so the slab comes up where the ports are. On wider slabs and ordinary ground, AP Lift 430 is the usual choice, and its longer window gives a crew more working time.
Cure follows almost immediately. The data sheet publishes 90 percent of full strength in about 15 minutes, which is why slab lifting is typically a same-day return to service instead of a multi-day closure. Confirm return to service for your loading and site conditions before scheduling traffic.
Technical specifications
Published properties
Cured foam, free rise
Property | Value | Method |
|---|---|---|
Density, free rise | 3 lb foam. Nominal 3 lb/ft³, range 2.75 to 3.25 lb/ft³ (44 to 52 kg/m³) | ASTM D1622 |
Compressive strength, free rise | 50 psi, or 7,200 psf (345 kPa) | ASTM D1621 / D1622 |
Shear strength, free rise | 25 psi, or 3,600 psf (172 kPa) | ASTM C273 |
Flexural strength | 90 psi, or 13,000 psf (621 kPa) | ASTM D790 |
Closed cell content | 92% | ASTM D6226 |
Water absorption | Less than 8% | ASTM D2842 |
Dimensional change, thermal and humid aging | 1 percent volume | ASTM D2126 |
Expansion, unconfined | Up to 25 times liquid volume | TDS |
Strength development | 90% of full strength in about 15 minutes | TDS |
NY-Panel result | Pass, 92.3% density retention | TDS |
Cured foam, confined
Property | 1.5x | 2x | 3x |
|---|---|---|---|
Compressive strength, confined | 88 psi, 12,700 psf | 130 psi, 18,700 psf | 210 psi, 30,200 psf |
Shear strength, confined | 44 psi, 6,340 psf | 65 psi, 9,360 psf | 105 psi, 15,100 psf |
Confined values are what the foam does once it is compacted against soil and the underside of a slab, which is why they run well above the free-rise figures. The data sheet labels these levels 1.5x, 2x and 3x without stating what the multiplier is measured against, so confirm the basis with Technical Services before using them in a submittal.
Reaction profile at 105°F, Fast compared with standard
Stage | AP Lift 430 Fast | AP Lift 430 | Method |
|---|---|---|---|
Cream time | 2 seconds | 2 seconds | ASTM D7487 |
Tack-free time | 11 seconds | 17 seconds | ASTM D7487 |
Rise time | 18 seconds | 23 seconds | ASTM D7487 |
Everything structural is the same: both are 3 lb foams at 50 psi free-rise compressive strength, 92 percent closed cell, 25 times unconfined expansion, 15 minutes to 90 percent of full strength, 200 cP at 110 degrees F. Only the reaction window differs. Choose AP Lift 430 Fast on sidewalks, patios, and other narrow or lightweight slabs, where a slower foam can cross the slab and lift the wrong end. Choose AP Lift 430 on wider slabs and ordinary ground, where the longer window gives a crew more working time.
Liquid components
Property | A side | B side |
|---|---|---|
Specific gravity | 1.23 | 1.05 |
Weight per gallon | 10.25 lb | 8.7 lb |
Viscosity at 110°F | 200 cP (200 mPa·s), ASTM D4878 | |
Equipment settings, not ambient air temperature
Setting | Temperature | Note |
|---|---|---|
A-side material heater | 100°F (38°C) | Machine setting |
B-side material heater | 110°F (43°C) | Machine setting |
Hose | 105°F (41°C) | Machine setting |
Handling and storage
Property | Value | Method / Note |
|---|---|---|
Composition | Two component structural polyurethane foam, heated and mixed at the gun | TDS |
Storage temperature | 50 to 80°F (10 to 26°C) | TDS |
Shelf life | 24 months in unopened containers stored within the range above | TDS |
Packaging | 100-gallon and 500-gallon units, each a matched A-side and B-side pair | Product page |
AP Lift 430 Fast is a 3 lb foam. Density is how these foams are graded, so a 3 lb, a 4 lb and a 6 lb foam are different products for different loads, and the range above is the manufacturing tolerance on that grade, not a choice. Free-rise values are unconfined laboratory figures. This data sheet publishes no tensile strength and no mix ratio. Temperatures in the equipment table are material temperatures at the machine, not air temperature limits for the job site, and no ambient application range is published for this product. Source: AP Lift 430 Fast Technical Data Sheet, Rev. 1/20/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.
Downloads
Data sheets, specifications, and procedures
Technical Data Sheet (TDS)
Published properties · PDF
Safety Data Sheet, Part A
AP 400 Series A side · PDF
Safety Data Sheet, Part B
AP Lift 430 Fast B side · PDF
Specification, CSI 31 43 00
Concrete raising · PDF
Procedures, Slab Lift Process
Field procedure · PDF
Slab Lifting Brochure
Request the brochure · Short form
Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.
Compatible equipment & accessories
What you need to install AP Lift 430 Fast
Two-component proportioner with material heaters, required. AP Lift 430 Fast cannot be poured or hand mixed. View proportioners
MixMaster Pro slab lifting gun, the gun named in the CSI 31 43 00 specification. View gun
PX-7 slab lifting gun, the alternate gun option. View gun
3/8 inch hammer-in injection ports, named in the CSI 31 43 00 specification. View ports
Alchatek Surface Guard 125, protects finished surfaces during injection. View accessory
Alchatek Pump Flush, reusable, biodegradable pump flush for shutdown. View flush
Alchatek Soak 130, cured-polyurethane cleaning solvent. View solvent
Related articles & guides
Learn the method behind the product
Concrete Leveling with AP 430, 440 and 475
Product comparison
Polyurethane Slab Lifting Explained
Method explainer
Slab Lifting with Polyurethane Foam
Field walk-through
Frequently Asked Questions
Lifting sidewalks, walkways, patios, and other narrow or lightweight concrete slabs back to grade, filling the voids beneath them, stabilizing the soil that let them settle, and filling abandoned pipes and mine shafts. It is the super fast reacting version of AP Lift 430.
The reaction window, and nothing else that matters structurally. Both are 3 lb foams with the same 50 psi free-rise compressive strength, 92 percent closed cell content, 25 times unconfined expansion, and 15 minutes to 90 percent of full strength. AP Lift 430 Fast reaches tack free in 11 seconds against 17, and completes its rise in 18 seconds against 23.
When the slab is narrow or lightweight. On a sidewalk or patio only a few feet across, a slower foam has room to travel to the far edge before it firms up, which lifts the end that never settled. AP Lift 430 Fast reaches tack free in 11 seconds instead of 17, so the lift stays under the ports. On wider slabs and ordinary ground the standard product is the usual choice, and its longer working window is easier to manage.
Because the slab is narrow. Injected foam spreads in every direction, and on a walkway only a few feet across it can reach the far edge while it is still liquid, putting the lift under the section that never settled and leaving the trip hazard worse than it started. A super fast reacting foam such as AP Lift 430 Fast turns to structure under the port in 11 seconds instead of 17, so the slab comes up where the ports are.
It is a 3 lb foam. Published free-rise values are 50 psi compressive strength, or 7,200 psf, and 25 psi shear strength, or 3,600 psf, at a nominal cured density of 3 pounds per cubic foot. Flexural strength is 90 psi and the foam is 92 percent closed cell. Confined beneath a slab the foam reaches a higher density and higher strength than these free-rise figures.
They are compressive and shear values measured at three levels of confinement, labelled 1.5x, 2x and 3x on the data sheet, running from 88 psi compressive at 1.5x up to 210 psi at 3x. The data sheet does not define what the multiplier is measured against, so confirm the basis with Technical Services before using these values in a submittal.
The technical data sheet publishes an unconfined expansion of up to 25 times its liquid volume. Unconfined is a laboratory free-rise figure. Under a slab the foam is confined, so real expansion is lower and the resulting density is higher.
The data sheet publishes 90 percent of full strength in about 15 minutes, which is why slab lifting is generally described as same-day work rather than a multi-day cure. Confirm return to service for your loading and conditions with Technical Services.
Both. The foam expands into voids and weak ground beneath the slab, compresses and densifies that soil as it expands, then cures into a closed-cell structural mass that carries load. Lifting the slab without addressing the ground beneath it is what lets a slab settle again.
A two-component proportioner with material heaters, plus a slab lifting gun. This is not a product that can be poured or hand mixed. The two sides are heated, metered, and mixed at the gun, then injected through small ports drilled in the slab.
The reaction is temperature dependent. The data sheet gives equipment settings of 100 degrees F on the A side, 110 degrees F on the B side, and 105 degrees F at the hose. Those are material temperatures at the machine, not air temperature limits for the job site.
The data sheet publishes a shelf life of 24 months in unopened containers stored between 50 and 80 degrees F. Both sides should be kept sealed and within that range.
Yes. Alchatek publishes a CSI Section 31 43 00 specification, Concrete Raising, which names AP Lift 430 Fast alongside AP Lift 430 as an acceptable product. It is in the downloads on this page, along with the slab lift field procedure.
100-gallon and 500-gallon units. Each unit is a matched pair of A-side and B-side containers.
Proof & Verification
APLIFT430FAST-PB-02
Slot 2: Performance Data Point or Credential
Narrow walkway, a patio you would rather not make worse, or a slab that lifted at the wrong end last time? Talk the slab and the reaction window through before the ports go in.
For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.