Concrete Leveling & Soil Stabilization · Equipment
Slab Lifting Pumps, Proportioners and Geotech Equipment
The proportioners, guns, skid systems, rigs, and soil testing instruments behind slab lifting and deep soil injection, with published specifications so you can match the machine to the material, the power on site, and the size of the work.
ISO 9001 Certified Manufacturer
Alchatek-Built Rigs, One-Year Workmanship Warranty
On this page:
In short
What Alchatek supplies for slab lifting and soil work, and what it builds
Alchatek supplies the full equipment line for polyurethane slab lifting and deep soil injection: four PMC two-component proportioners, three injection guns, a gas-powered skid system, two soil testing instruments, and custom-built rigs on two platforms, a V-nose trailer and a box truck build-out. The proportioners and one gun are PMC equipment. The other guns, the skid system, and the rigs are Alchatek equipment.
Every unit here is named for the company that actually makes it, because what Alchatek builds and what it supplies are covered differently. The warranty section sets out which document covers what.
Choose your equipment
Match the machine to the material, the power, and the size of the work
Three questions settle it, in order: what you are injecting, what electrical power you can bring to the job, and how much work you place in a week. Start with the material, because slab lifting foam and deep soil injection resin run through different machines. The units below are grouped by what they do, and each one opens with the condition it fits.
Two-component proportioners
The core of a slab lifting rig. A proportioner heats and meters the A and B sides of a two-component foam and delivers them under pressure to the gun, where they mix. The AP Lift foams cannot be poured or hand mixed; one of these is required. All four are PMC machines rated at 2000 psi, and they differ by output, hose length, and the electrical power they need.
If you are running slab lifting foam on single-phase power, or you are buying your first proportioner
PMC PH-2 2000
The single-phase entry point. Horizontal 16:1 ratio pumps with 10.5 kilowatt heaters deliver 28 pounds per minute to a 410 foot maximum hose length. Lower output than the PH-40 and Premier, but it runs where three-phase power is not available.
If you want a 40 pound per minute proportioner and need to match it to the power you have, from single-phase to heavy three-phase
PMC PH-40
The configurable production proportioner. Size 120 pumps deliver 40 pounds per minute to 410 feet of hose in four configurations that differ by heater capacity and electrical phase, from a single-phase 15 kilowatt build to a three-phase 21 kilowatt build. See the configuration table below.
If you are running one gun on three-phase power and want a fixed, no-options production machine
PMC Premier
The fixed-configuration three-phase proportioner. Size 120 pumps with 18 kilowatt heaters deliver 40 pounds per minute to a single 410 foot hose, drawing 67 amps at 3 by 230 volts.
If you want two guns working from one machine
PMC Premier Mach 2
The two-output version of the Premier. Same 40 pounds per minute, 2000 psi and 18 kilowatt heaters, split across two outputs at 260 feet of hose each, so two operators can lift from one proportioner.
Skid system for Deep Lock® single-component soil injection
Deep Lock® is Alchatek's deep soil injection stabilization system, and it is a different job from lifting a slab. The single-component resin goes down injection pipes into weak soil, often far from the truck and often where there is no power, and the machine has to deliver at pressure over long hose lines and keep count of what went down each one.
If you are stabilizing soil at depth, running long hose lines, or working where there is no site power
PolyShark
A gas-powered high-pressure injection skid. The gas over hydraulic piston pump delivers up to 2.35 gallons per minute at 3600 psi, with the hydraulic fluid section moved front and center for easier maintenance. Two hose reels on stainless steel ball bearings and two flow meters that record exactly how much material went down each line, which matters when the injection is out of sight.
Injection guns
Where the two components meet and go into the ground. The gun has to handle back-pressure from beneath a slab and has to clean up between shots, and the three here solve that in different ways.
If you are lifting slabs from a proportioner and want the gun engineered for back-pressure
MixMaster Pro
The standard slab lifting gun. A stainless steel gun block with fully mechanical actuation, no side seals or O-rings in the mixing block, integrated rebuildable check valves, and a water-based flush. Uses the 3/8 inch injection port.
If you want a gun that clears itself mechanically after every shot, with no solvent and no air purge
PMC PX-7
A valving rod mechanically purges mixed material from the mixing module on each shot, so there is no solvent flushing or air purge to manage. Airless atomization, internal impingement, a precision-ground single-piece valving rod, rebuildable manual valves, a hardened stainless gun block, and CE certification. Economically priced.
Soil testing instruments
These are diagnostic tools used before a repair, not repair equipment. They tell you how strong the ground is and what is under the slab, which decides whether the job is a lift, a soil stabilization job, or both, before any material is ordered.
If you need to know how strong the soil is and how deep the weak layer runs before you quote
Alchatek Pagani DPM-30
A portable dynamic cone penetrometer for continuous testing on the jobsite, including sites too tight for standard equipment. A 66 pound (30 kilogram) hammer with a 7.87 inch (200 millimeter) stroke drives the cone, a hydraulic extractor pulls the rods and casing back out, and a pedal-operated hydraulic distributor with quick-connect fittings runs it. Electric motor or gasoline engine.
If you need to see what is beneath a slab or in the soil without opening it up
Deep Look® Ground Penetrating Radar
A wireless ground penetrating radar system operating from 50 to 1400 megahertz with CBD antennas, for locating voids, utilities, and changes in the subsurface before a repair is scoped.
Custom slab lifting rigs
A rig is the proportioner, generator, compressor, hose reels, and material handling built into a mobile platform as one working system. Alchatek builds them on two platforms. These are configured builds, not fixed models: the platform sets the size, and the conversation sets what goes in it.
If you want the smallest complete rig, towable behind a pickup
V-nose trailer rig
A 16 to 20 foot V-nose trailer built out as a complete slab lifting and soil stabilization rig. Trailer included.
If you already run box trucks and want the system built into one
Box truck build-out
A 16 to 28 foot box truck fitted out as a complete rig. You supply the truck; Alchatek builds the system into it.
Not sure whether the job is a lift or a soil stabilization job yet? The condition decides the material and the material decides the machine, so settle the method first. See Concrete Leveling and Stabilization or Soil Stabilization & Settlement Control, or send us the condition.
Specifications
Published specifications, side by side
PMC two-component proportioners
Specification | PMC PH-2 2000 | PMC PH-40 | PMC Premier | PMC Premier Mach 2 |
|---|---|---|---|---|
Maximum operating pressure | 2000 psi | 2000 psi | 2000 psi | 2000 psi |
Output | 28 lb/min | 40 lb/min | 40 lb/min | 40 lb/min |
Maximum hose length | 410 ft | 410 ft | 410 ft | 260 ft on each of two outputs |
Pumps | 16:1 ratio horizontal pumps | Size 120 pumps | Size 120 pumps | Size 120 pumps |
Heaters | 10.5 kW | 15, 18 or 21 kW by configuration | 18 kW | 18 kW |
Motor | Not published | 5 hp | 5 hp | 5 hp |
Electrical | Single phase | Single or three phase by configuration, 220 V | Three phase, 3 by 230 V, 67 A | Three phase, 3 by 230 V, 77 A |
PMC PH-40 configurations
Configuration | Heaters | Motor | Phase | Amperage at 220 V |
|---|---|---|---|---|
PH-40 1207A16 | 15 kW | 5 hp | Single phase | 130 A |
PH-40 1207A30 | 15 kW | 5 hp | Three phase | 80 A |
PH-40 1209A30 | 18 kW | 5 hp | Three phase | 93 A |
PH-40 1210A30 | 21 kW | 5 hp | Three phase | 106 A |
Source: Alchatek Slab Lifting Pumps and Guns page, as published. All four PH-40 configurations deliver 40 lb/min at 2000 psi to a 410 ft maximum hose length. PMC is Polyurethane Machinery Corporation; confirm against PMC's current specification before specifying.
PolyShark skid system
Specification | Value | Note |
|---|---|---|
Maximum delivery | 2.35 GPM | Product page |
Maximum operating pressure | 3600 psi | Product page |
Engine | 200 cc gas engine, gas over hydraulic piston pump | Product page |
Hose reels | Two, on stainless steel ball bearings, no bushings | Product page |
Flow meters | Two, recording material delivered through each hose line | Product page |
Soil testing instruments
Specification | Alchatek Pagani DPM-30 | Note |
|---|---|---|
Test type | Continuous dynamic cone penetrometer test | TDS Rev. 1/21/2026 |
Hammer | 66 lb (30 kg) | Soil testing page |
Stroke | 7.87 in (200 mm) | Soil testing page |
Drive | Electric motor or gasoline engine | Soil testing page |
Extraction | Hydraulic extractor for rods, casing and samplers; pedal-operated hydraulic distributor; quick-connect fittings | TDS |
The Deep Look® ground penetrating radar publishes an operating range of 50 to 1400 MHz with CBD antennas and wireless operation; no further specification is published. Specifications vary with site conditions; confirm against the current data sheet before specifying.
Warranty
Which warranty covers what
Equipment is covered by the Alchatek Equipment and Rig Limited Warranty, Form 9301, a different document from the one covering foams and resins. Coverage depends on who manufactured the part, and a rig is more than one company's work, so it is worth two minutes before you buy.
What Alchatek warrants
For one year from the date of shipment, items Alchatek manufactures or fabricates, including the MixMaster gun. Also, for one year from shipment, the fabrication, assembly, plumbing, hose routing, wiring, mounting, and integration workmanship of any rig, skid, or packaged system sold under the Alchatek name, whether Alchatek or a contract builder assembled it. That covers system-level workmanship only.
What carries no Alchatek warranty
Pumps, hoses and hose assemblies, engines, gasoline and diesel generators, air compressors, air dryers, hose reels, trailers and chassis, and electrical, pneumatic, and hydraulic components are not manufactured by Alchatek. The sole warranty on any of them is the warranty of its own manufacturer, on that manufacturer's terms and for that manufacturer's period, whether you buy the component on its own or it is built into a rig. A PMC proportioner carries a PMC warranty. Alchatek also does not warrant a failure of an Alchatek-built system that is caused by a third-party component.
Before you buy a used rig
Coverage is for the original purchaser only. It ends automatically on any sale, transfer, lease, rental, or assignment, so a used, leased, or rented rig is not covered.
Documentation
Data sheets
Assembling a submittal package or comparing units? Every data sheet, specification, and certificate lives in the central Downloads library.
The materials
What this equipment runs with
Systems & Products, the slab lifting foams and soil injection resins these machines are built to place.
Geotechnical Accessories, the heated hose, ports, fittings, filters, and consumables a proportioner and gun run with.
Leak Seal Equipment, the injection pumps and gun for crack injection and leak sealing rather than slab lifting.
Training and startup
Getting a crew running on the equipment
A proportioner is only as good as the crew running it. Slab lifting rewards crews trained on the foam, the gun, and the reading of the slab together, and a rig commissioning is the wrong place to learn any of the three.
Training & Education
For training a crew on the injection work itself
Technical Services
For rig commissioning, startup, and unit-specific questions
Contractor Tools
For the estimators and selectors that shape a job before it is scoped
Frequently Asked Questions
It depends on the power you can bring to the job. The PMC PH-2 2000 runs on single-phase power at 28 pounds per minute and is the entry point. The PMC PH-40 and PMC Premier run at 40 pounds per minute and most configurations need three-phase power. If you are not sure what your site or rig can supply, Technical Services will walk through it before you buy.
Heater capacity and electrical phase. All four deliver 40 pounds per minute at 2000 psi with a 410 foot maximum hose length. Configuration 1207A16 runs 15 kilowatt heaters on single-phase power at 130 amps. Configurations 1207A30, 1209A30 and 1210A30 run 15, 18 and 21 kilowatt heaters on three-phase power at 80, 93 and 106 amps. More heater capacity keeps material temperature up on long hose runs and in cold weather.
The Mach 2 has two outputs. Both deliver 40 pounds per minute at 2000 psi with 18 kilowatt heaters on three-phase power. The Premier feeds one hose to 410 feet. The Premier Mach 2 feeds two hoses to 260 feet each, so two guns can work from one machine.
Not always. The PMC PH-2 2000 and the PMC PH-40 configuration 1207A16 run on single-phase power. The other PH-40 configurations, the Premier and the Premier Mach 2 need three-phase power. On a rig, that power usually comes from an onboard generator, which is one of the things a rig build sorts out for you.
Deep soil injection. It is a gas-powered skid system that delivers up to 2.35 gallons per minute at 3600 psi through two hose reels, with two flow meters that record exactly how much material went down each line. It is the pump for Deep Lock soil stabilization work, and the gas engine means it runs where there is no site power.
How strong the ground is, and how deep the weak layer runs. It is a dynamic cone penetrometer: a 66 pound hammer drives a cone into the soil and the blow count per depth tells you where the bearing changes. That reading decides whether a job is a slab lift, a soil stabilization job, or both, before any material is ordered.
No. They are two different things with similar names. Deep Look is a ground penetrating radar unit used to look beneath a slab or into soil before a repair. Deep Lock is the Alchatek deep soil injection stabilization system, which is a repair method and the materials and equipment that deliver it. One finds the problem, the other fixes it.
The trailer build does. The V-nose rig is built on a trailer Alchatek supplies. The box truck rig is a build-out: you supply the truck and Alchatek builds the system into it.
No. A pump carries the warranty of the company that manufactured it, on that manufacturer's terms, so a PMC proportioner carries a PMC warranty. What Alchatek warrants is what Alchatek builds: its own equipment for one year from shipment, and the system-level workmanship of an Alchatek-built rig for one year from shipment. The Equipment and Rig Limited Warranty is the governing document.
The condition decides the material, and the material decides the machine. Send us the condition and we will tell you what the work actually needs before you spend on equipment.
For specifications, see the data above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.