Leak Sealing & Water Control · Equipment

Crack Injection Pumps and Leak Seal Equipment

The pumps and guns Alchatek's leak seal resins are built to run through, with published specifications so you can match the unit to the resin and the job before you buy.

ISO 9001 Certified Manufacturer

Stock Titan Units, Factory Warranty Intact

In short

What Alchatek supplies for leak sealing, and what it builds

Alchatek supplies four injection pumps and one injection gun for leak sealing and water control, ranging from a 35 pound electric pump for crack and joint work up to a gas-powered unit for high-output curtain grouting. Three of the pumps are stock Titan units. The Acrylate Gel Pump and the SealMaster gun are Alchatek equipment.

Every unit here is named for the company that actually makes it, because what Alchatek manufactures and what it supplies are covered differently. The warranty section sets out which document covers what.

Choose a pump

Match the equipment to the resin and the job

Three questions settle it, in order: which resin you are injecting, how much you place in a week, and what power you have on site. Start with the resin, because it is the constraint that cannot be worked around. The units below are grouped by what they do, and each one opens with the condition it fits.

Electric injection pumps

Airless electric pumps for injecting single-component polyurethane resin into cracks and joints. Both run on site power and both are light enough for one person to reposition.

If you are injecting single-component polyurethane resin into cracks and joints on a normal repair workload

Titan Impact 440

The standard crack injection pump. A 7/8 horsepower DC motor drives it to 3300 psi, and at 35 pounds on the skid frame one person can move it.

Titan Impact 440 electric injection pump with hose for leak seal injection

If you are doing the same work but placing more resin each week, or you want output tracked on the unit

Titan Impact 640

Same weight and pressure as the 440 with higher delivery, plus a DigiTrac integrated digital display with an anti-theft lock.

High-output injection pumps

For curtain grouting, gushing leaks, and any work where the volume or the lack of site power rules out an electric pump.

If you are curtain grouting, chasing gushing leaks, or working where there is no power on site

Titan PowrTwin 8900 Plus

Runs on a 200 cc gas engine or a 2.0 horsepower electric motor, so it works where there is no site power. Output on gas is more than four times the Impact 440, at a higher working pressure. It weighs 155 pounds, so plan how it gets to the work.

Acrylic gel pumps

Acrylic resins are not polyurethane and are not injected with the same equipment. This is the pump specified for them.

If you are injecting acrylic gel, such as Spetec AG200, or another low-viscosity resin that mixes at 1:1

Alchatek Acrylate Gel Pump

A reciprocating positive displacement piston pump delivering material at 1:1 through stainless steel transfer components. Pneumatic, so it needs a compressor rather than site power, and it carries an integrated rinsing pump for shutdown.

Injection guns

Where the resin leaves the hose and enters the structure. Flow control at the gun matters when a crack takes resin unevenly.

If you need to adjust flow at the gun while you are injecting

Alchatek SealMaster Adjustable Flow Injection Gun

Adjustable flow at the point of injection, so the operator throttles at the crack instead of at the pump. Pairs with the electric injection pumps above.

Not sure which resin the condition calls for yet? The resin decides the pump, so settle the repair method first. See Leak Sealing & Water Control, or send us the condition.

Specifications

Published specifications, side by side


Injection pumps

Specification

Titan Impact 440

Titan Impact 640

Titan PowrTwin 8900 Plus

Maximum delivery

0.54 GPM

0.70 GPM

2.35 GPM on gas, 1.25 GPM on electric

Maximum operating pressure

3300 psi (22,753 kPa)

3300 psi (22,753 kPa)

3600 psi (24,821 kPa)

Weight, skid frame

35 lb (15.88 kg)

35 lb (15.88 kg)

155 lb (70.31 kg)

Power

7/8 hp DC motor

7/8 hp DC motor

200 cc gas engine or 2.0 hp electric motor

Suggested weekly capacity

50 to 100 gal (189 to 379 L)

75 to 100 gal (284 to 379 L)

Not published here, confirm with Technical Services

Integrated display

No

DigiTrac digital display with anti-theft lock

No

Source: Alchatek Electric Injection Pumps Technical Data Sheet, Rev. 1/21/2026.


Alchatek Acrylate Gel Pump

Specification

Value

Note

Injection pressure

150 to 1500 psi (10 to 100 bar)

Variable

Maximum delivery rate

0.26 gal/min (8 L/min)

TDS

Mixing ratio

1:1

TDS

Transmission ratio

1:13

TDS

Air consumption

35 ft³/min (1 m³/min)

Compressor supplied separately

Maximum air pressure

116 psi (8 bar)

TDS

Weight

64.5 lb (29.3 kg)

TDS

Dimensions, L by W by H

30.7 by 15.3 by 31.4 in (78 by 39 by 80 cm)

TDS

Integrated rinsing pump

1.34 gal/min delivery, 105 to 3300 psi variable, 1:28 ratio

TDS

Storage temperature

50 to 80°F (10 to 26°C)

TDS

Source: Alchatek Acrylate Gel Pump Technical Data Sheet, Rev. 1/19/2026. For industrial use only; review the safety data sheet for the resin before use. Specifications vary with site conditions; confirm against the current data sheet before specifying.

Warranty

Which warranty covers what

Equipment is covered by the Alchatek Equipment and Rig Limited Warranty, Form 9301, a different document from the one covering resins and materials. Coverage depends on who manufactured the part, so it is worth two minutes before you buy.

What Alchatek warrants

For one year from the date of shipment, items Alchatek manufactures or fabricates. Also, for one year from shipment, the fabrication, assembly, plumbing, hose routing, wiring, mounting, and integration workmanship of any rig, skid, or packaged system sold under the Alchatek name. That covers system-level workmanship only.

What carries no Alchatek warranty

Pumps, hoses and hose assemblies, engines, gasoline and diesel generators, air compressors, air dryers, hose reels, trailers and chassis, and electrical, pneumatic, and hydraulic components are not manufactured by Alchatek. The sole warranty on any of them is the warranty of its own manufacturer, on that manufacturer's terms and for that manufacturer's period.

Because the Titan pumps on this page are stock units, the Titan factory warranty applies to them as Titan writes it.

Before you buy a used unit

Coverage is for the original purchaser only. It ends automatically on any sale, transfer, lease, rental, or assignment, so a used, leased, or rented unit is not covered.

Read the Equipment and Rig Limited Warranty in full →

Documentation

Data sheets

Assembling a submittal package or comparing units? Every data sheet, specification, and certificate lives in the central Downloads library.

The materials

What this equipment runs with

  • Systems & Products, the leak seal resins and acrylic gels these pumps are built to inject.

  • Leak Seal Accessories, the packers, ports, valves, oakum, and consumables an injection pump runs with.

  • Geotechnical Equipment, the proportioners, guns, and rigs for slab lifting and soil stabilization rather than leak sealing.

Training and startup

Getting a crew running on the equipment

Buying the pump is the easy part. Injection work rewards crews trained on the resin and the technique together, and the first job is an expensive place to learn.

Frequently Asked Questions

For most crack and joint injection work with single-component polyurethane resin, the Titan Impact 440 is the starting point. Step up to the Titan Impact 640 for higher weekly volume, or to the Titan PowrTwin 8900 Plus when you need much higher output or have no site power. For acrylic gel, use the Alchatek Acrylate Gel Pump instead.

Output and tracking. The Impact 440 delivers up to 0.54 gallons per minute and the Impact 640 delivers up to 0.70 gallons per minute. Both reach 3300 psi, both weigh 35 pounds on the skid frame, and both run a 7/8 horsepower DC motor. The 640 adds an integrated digital display with an anti-theft lock.

When output or power is the constraint. The PowrTwin 8900 Plus delivers up to 2.35 gallons per minute on its gas engine and up to 1.25 gallons per minute on its electric motor, at up to 3600 psi. The gas engine also lets it run where there is no site power. It weighs 155 pounds, so it is a larger unit to move.

No, not any more. Alchatek used to modify these pumps, but a Titan design change ended that practice, so the units Alchatek supplies today are stock Titan pumps. One practical benefit is that the Titan factory warranty on them is intact.

A pump carries the warranty of the company that manufactured it, on that manufacturer's terms. Items Alchatek manufactures or fabricates carry a one-year Alchatek limited warranty from the date of shipment. The Equipment and Rig Limited Warranty is the governing document and it sets out exactly what is and is not covered.

Yes. The Alchatek Acrylate Gel Pump is pneumatic, so it runs on compressed air rather than on electricity. It consumes about 35 cubic feet per minute at a maximum air pressure of 116 psi. The compressor is not supplied with the pump.

The Alchatek Acrylate Gel Pump. It is built for acrylic gels and other low-viscosity resins that mix at 1:1, and it has stainless steel transfer components. Before running any resin through a pump it is not specified for, check with Technical Services.

No. Hoses and hose assemblies, generators, air compressors, air dryers, and hose reels are supplied separately, are not manufactured by Alchatek, and carry no Alchatek warranty. Ask Technical Services what a complete setup needs for the work you are doing.

Use Alchatek Pump Flush at shutdown. It is a reusable, biodegradable flush. Alchatek Soak 130 is the solvent that removes cured polyurethane from equipment. Both are listed with the leak seal accessories.

Yes. Training and Education covers the injection work itself, and Technical Services can walk through startup and setup on a specific unit. Ask before the first job rather than during it.

The resin decides the pump, and the condition decides the resin. Send us the condition and we will tell you what the work actually needs before you spend on equipment.

For specifications, see the data above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.