Leak Sealing & Water Control · Acrylic Resin
Spetec AG200 Acrylic Injection Resin
A three-component acrylic hydrogel that mixes to near the viscosity of water, so it reaches gravel nests, porous masonry, and fine defects a polyurethane resin would bridge.
NSF/ANSI/CAN 61 & 372 Certified · Certified for contact with drinking water. The listing carries use restrictions.
Acrylic hydrogel
Three component
Ultra low viscosity
Curtain grouting
On this page:
What it is
An acrylic hydrogel thin enough to reach what polyurethane cannot
Spetec AG200 is a three-component acrylic injection resin, a water-swelling hydrogel that cures into a soft, elastic gel, used to waterproof concrete, masonry, and rock. Mixed, it runs at 6 cP at 68°F, close to the viscosity of water. That is the whole point of the product: it penetrates gravel nests, fine defects, and porous masonry that a thicker resin would bridge rather than fill.
AG200 is the one Spetec Leak Seal product that is not single component. It is supplied as three parts, an amber liquid, a white powder, and a colorless liquid, and it is injected with a two-component acrylic pump fitted with a clean-out line.
Where it is used
What AG200 is used for
AG200 is part of the Spetec Leak Seal Systems line and sits in the Leak Sealing & Water Control solution family.
Waterproofing gravel nests and honeycombing in concrete
Underground concrete and masonry waterproofing
Crack injection, including cracks in rock
Curtain grouting behind walls and floors
Re-injectable injection hose systems
Below-grade expansion joints
Consolidating soil to stop erosion around floors and walls
Structures in contact with drinking water, within the restrictions of the NSF listing
How it works
How AG200 reaches a defect a polyurethane resin would bridge
AG200 is mixed and injected at close to the viscosity of water, so it travels into fine defects and porous material, then reacts to form a water-swelling hydrogel that cures soft and elastic. Pot life at 68°F runs from 9 seconds to 7 minutes, so the crew sets the reaction to the work in front of them instead of racing a fixed window.
The cured gel is soft by design. Elongation at break is 510 percent, with a tensile strength of 5.80 psi and an E-modulus of 37.7 psi, so it seals by filling and swelling rather than by adding strength. Per the data sheet it stays durable through wet and dry conditions and shows low shrinkage.
Technical specifications
Published properties
Mixed resin
Property | Value | Method |
|---|---|---|
Composition | Three component; supplied as an amber liquid, a white powder, and a colorless liquid | TDS |
Mixed viscosity at 68°F | 6 cP (6 mPa·s) | ASTM D4878 |
Pot life at 68°F | 9 seconds to 7 minutes | DIN EN 14022 |
Cured gel
Property | Value | Method |
|---|---|---|
Consistency | Soft elastic | - |
Color | Amber | - |
Elongation at break | 510% | DIN EN ISO 527-3 |
Tensile strength | 5.80 psi (40 kPa) | DIN EN ISO 527-3 |
E-modulus | 37.7 psi (260 kPa) | DIN EN ISO 527-3 |
Water absorption | 125% | DIN EN ISO 62 |
Handling & certification
Property | Value | Method / Note |
|---|---|---|
Application temperature | 41–104°F (5–40°C) | TDS |
Storage | 50–80°F (10–26°C) | TDS |
Shelf life | 24 months, unopened, within storage range | TDS |
Packaging | 5-gallon pail and 250-gallon tote | Product page |
Certification | NSF/ANSI/CAN 61 and 372. Certified for contact with drinking water. The listing carries use restrictions, including a minimum tank volume and an exclusion for pipe application. See the certificate. | TDS Rev. 4/30/2026 and NSF certified product listing |
Source: Spetec AG200 Technical Data Sheet, Rev. 4/30/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.
Downloads
Data sheets and certificates
Technical Data Sheet (TDS)
Published properties · PDF
Safety Data Sheet (SDS)
Handling & safety · PDF
NSF/ANSI/CAN 61 & 372 Certificate
Certified product listing · PDF
Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.
Compatible equipment & accessories
What you need to inject AG200
Two-component acrylic pump with a clean-out line, recommended for AG200. An acrylic system needs its own pump and clean-out procedure, not a polyurethane setup. View pumps
Injection valves and packers, for setting and injecting cracks, joints, and penetrations. View accessories
Alchatek Gel Reinforcing Agent, optional additive for AG200. View
Re-injectable injection hose system, for construction joints designed to be re-grouted later. View the system
Related articles & guides
Learn the method behind the product
Spetec Acrylate Grouts
Method explainer
Hydrophobic Polyurethanes vs Hydrophilic Polyurethanes
Chemistry comparison
Sealing Leaks in a Historic Brick Wall with Spetec AG200
Field walk-through
Frequently Asked Questions
No. AG200 is acrylic. It is a water-swelling hydrogel based on acrylic monomers, which is a different chemistry from the Spetec polyurethane injection resins and behaves differently in the crack.
Three. AG200 is the one Spetec Leak Seal product that is not single component. It is supplied as an amber liquid, a white powder, and a colorless liquid, and it is injected with a two-component acrylic pump fitted with a clean-out line.
Published mixed viscosity is 6 cP at 68 degrees F, which is close to the viscosity of water. That is the reason to reach for AG200: it penetrates gravel nests, fine defects, and porous masonry that a thicker polyurethane resin would bridge rather than fill.
Yes, that is one of its main uses. Because it mixes to near the viscosity of water it travels into gravel nests and honeycombing in concrete, into porous masonry, and into cracks in rock, then reacts to form a water-swelling gel that fills the void.
AG200 is certified to NSF/ANSI/CAN 61, which covers contact with drinking water, and to NSF/ANSI/CAN 372, which covers lead content. The listing carries use restrictions, including a minimum tank volume and an exclusion for pipe application, so read the certificate and confirm the certification is current before specifying.
Published pot life at 68 degrees F runs from 9 seconds to 7 minutes, so reaction time is set to the job rather than fixed. Confirm the working window for your mix and temperature against the current data sheet before injecting.
Very. Published elongation at break is 510 percent. The gel is soft by design, with a tensile strength of 5.80 psi and an E-modulus of 37.7 psi, so it seals by filling and swelling rather than by adding strength.
Waterproofing gravel nests and honeycombing in concrete; underground concrete and masonry waterproofing; crack injection, including cracks in rock; curtain grouting; re-injectable injection hose systems; below-grade expansion joints; and consolidating soil to stop erosion around floors and walls.
A two-component acrylic pump fitted with a clean-out line is recommended, along with injection valves and packers. Do not use a cured-polyurethane solvent to clean an acrylic system; follow the pump manufacturer's clean-out procedure.
Chemistry and reach. The polyurethane resins react with water and expand into a foam, and they are thicker. AG200 is acrylic, mixes to near the viscosity of water, and cures into a soft water-swelling gel. Reach for AG200 when the defect is too fine or too porous for a polyurethane resin to enter, and for a polyurethane resin when the job needs an expanding foam that fills a moving crack.
Unopened containers have a 24 month shelf life when stored between 50 and 80 degrees F.
Proof & Verification
AG200-PB-01
Sealing Hairline Concrete Cracks
Deciding whether the defect calls for an acrylic resin or a polyurethane one? That choice is easier to make before the packers are set than after.
For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.