Deeper weak soils extend below the slab zone
Solution · Concrete Leveling and Stabilization
Restore elevation, improve contact and bearing beneath concrete surfaces, and choose a leveling sequence that fits what is actually failing below the slab.
NSF/ANSI 61 option in every density
ISO 9001 certified manufacturing
Soil tested before injection
In short
What is concrete leveling
and stabilization?
Concrete leveling and stabilization restores a settled slab to its correct elevation and stabilizes the ground beneath it so the correction holds. When the soils below are also failing, it pairs surface lift with deeper ground stabilization (Deep Lock® injection), so the method follows what’s actually failing under the slab, not just the visible drop.
The Depth Question
Slab Lifting is Only Skin Deepâ„¢
Lifting raises the slab. It doesn't always fix what's holding it up.
Injecting polyurethane directly under a slab restores elevation, and when the weak zone is shallow, that's often all a slab needs. But settlement frequently starts deeper in the soil strata. When it does, a lift-only repair corrects the surface while the real cause keeps working below, and the slab settles again. Deep Lock® injection treats those deeper soils directly, stabilizing the ground before a surface correction has to hold.
The only way to know how deep it goes is to measure it: a Dynamic Cone Penetrometer (DCP) test maps soil strength layer by layer before lift-only or Deep Lock® is chosen. How the test works is covered below.
Project Fit Snapshot
When does concrete
leveling and stabilization fit?
Find the situation that matches yours.
Short answer
Can concrete leveling solve every settled-surface problem by itself?
No. It is strongest where the surface needs correction and the ground below can be restored or improved enough to hold that correction. Broader weak-soil, recurring washout, or deeper instability problems may still require stabilization or paired repair logic.
Lift will hold, because the ground beneath can hold it.
A slab, walk, or pavement has settled, and the ground beneath it is stable
An approach slab or pavement transition has dropped, and the subgrade is intact
Keep reading. This method restores elevation and stabilizes the ground beneath so the correction holds.
Something below is still failing. Address it, or the slab settles again.
The soils below are weak or still moving
Add Deep Lock® soil stabilization. Neither lift nor stabilization alone produces a durable result when both conditions are present.
Water is actively removing soil
Start with erosion review & water control, or surface correction will recur
When to Escalate
When should Deep Lock® and Dynamic Cone Penetrometer testing replace a lift-only approach?
Technical review matters most when settlement is recurring, traffic-sensitive, tied to water, or likely to mean the ground below is failing in ways the surface doesn't fully show.
Settlement is recurring after a previous repair attempt
Location is traffic-sensitive: roadway, approach slab, loading area
Active water or drainage issues are present at the site
Consequence of incorrect method selection is high
Condition is unclear or difficult to narrow from surface review alone
Technical Services
Project-specific review when the condition requires it
Technical Services is the right next step when recurring settlement, active water, high-consequence exposure, or unclear soil and bearing conditions make page-level guidance insufficient. Direct review helps avoid the rework cycle that follows a mismatched repair method.
Know what's below before you inject
The Alchatek Pagani DPM-30 Dynamic Cone Penetrometer is how you find out. Drive it through the soil profile before injection and you get a continuous resistance reading, layer by layer, that shows where density drops, where bearing is unreliable, and how deep the treatment zone needs to go for Deep Lock® to hold.
It's a short in-situ test that tells you whether the project is a surface correction or a ground restoration, so the right one gets specified.
Diagnosis logic
What causes a
concrete slab to settle?
The visible drop in a slab, pavement, or approach usually means the ground below changed first. Matching the method to what actually failed below, not the visible gap, is what prevents repeat movement.
Diagnosis Before Methodâ„¢
The difference between a repair that lasts and one that fails.
Diagnosis
Identify the visible symptom
Understand what changed below
Then select the method
Match the method to what failed below
Confirm the correction holds
Method Limits
When is polyurethane
slab lifting not enough on its own?
Concrete leveling alone may not be enough when deeper weak soils, recurring migration, active washout, or broader instability are still driving the movement. Recognizing the limit early avoids a repeat repair.
FAQ
FAQs
Direct answers to the questions engineers, contractors, and owners ask most. When a project condition requires more than page-level guidance, Technical Services is the right next step.
The method
It is the controlled correction of elevation in settled slabs, pavements, or approaches combined with restoration of the ground beneath them.
Yes. Many projects require both, especially when the slab symptom and the failing ground beneath are part of the same problem.
No. Concrete leveling and stabilization restores elevation and the ground immediately beneath the slab. Soil stabilization addresses broader or deeper ground instability that may be driving the visible movement.
Polyurethane slab lifting and mudjacking can differ in weight, cure behavior, mobilization, water sensitivity, and fit. The right choice depends on the condition, access, performance objective, and how the ground beneath behaves.
It fits best when the surface needs elevation correction and the ground below can be restored or improved to hold that correction.
Small-diameter holes are drilled through the settled slab. Polyurethane resin is injected beneath it, where it expands to fill voids, restore contact between the slab and the ground, and lift the concrete back to the correct elevation. The material cures in minutes. The process is minimally invasive: no excavation, no heavy equipment, and surfaces are typically ready for use shortly after injection.
Diagnosis & causes
Hollow-sounding areas, localized drop, recurring movement, or visible loss of bearing can all indicate hidden cavities or loss of contact that should be evaluated before the repair method is finalized. See also: Voids Beneath Concrete.
Recurring movement usually means the repair sequence did not fully address what was actually causing the ground to fail. That is the point where deeper review, paired methods, or broader stabilization logic should be considered.
Yes. Water can weaken or wash out the soils beneath a slab, create voids, and leave the slab with less reliable bearing than it had originally.
Yes, in many cases. Approach slab settlement is a common application, but the embankment condition, traffic classification, and soil behavior must be evaluated before confirming method fit. See: Bridge Approach Settlement.
The polyurethane itself doesn't degrade underground. It's chemically inert, hydrophobic, and unaffected by groundwater. Once cured, it stays in place.
How long the correction holds depends on what's below the slab. When the ground beneath is stable, the lift can hold for the service life of the concrete. When the conditions that caused the original settlement are still active, such as ongoing water migration or unstable soil, the surface can move again. That's not a material failure; it's a site condition that wasn't fully addressed before the lift. The right answer to longevity starts with the diagnosis, not just the injection.
Documentation
Technical Data Sheets, Safety Data Sheets, Specifications, NSF Certificates, Application Guides, and Installation Procedures are available through Downloads. Engineering drawings and reference diagrams are available through Engineering Resources.
Return-to-service timing depends on the method, site conditions, traffic demands, and project constraints. The correct expectation should be set within the method and project review discussion rather than assumed in advance.
Once cured, polyurethane is chemically inert. It does not react with or leach into surrounding soil or groundwater, and it does not erode or break down underground. Alchatek resins are available with NSF/ANSI 61 certification for applications in or near potable water contact, which is the applicable standard for sensitive site conditions. SDS and NSF certification documents are available through Downloads.
When to escalate
Bring in Technical Services when the condition is recurring, traffic-sensitive, water-driven, high consequence, or difficult to narrow from page-level guidance alone. See: Technical Services.
When recurring movement, deeper weak soils, active water, or high-consequence exposure make a lift-only approach insufficient. The Dynamic Cone Penetrometer identifies the depth and extent of the problem before injection begins.
Concrete leveling and stabilization addresses the surface correction and the ground immediately beneath it. Soil stabilization addresses the deeper soil. The two are often paired when the slab problem is driven by broader instability below the slab zone.
Navigate
Related pages and resources
Start with the condition
Adjacent solutions
If a slab, walk, or pavement has dropped or gone uneven.
If the surface sounds hollow or has lost contact underneath.
If there is a bump or drop where a road meets a bridge.
If water is still moving soil out from under the surface.
If the ground itself is weak or still moving.
If water is actively getting in and needs to be stopped first.
Documentation
Direct support
Drawings, method guidance, and technical detail.
TDS, SDS, specifications, NSF certificates, case studies.
Project-specific review of method and sequence.
Send the condition and get a repair direction.
Proof & Verification
Named Project
A failed culvert washed out soil 28 feet under a Norcross plant’s lot. CIPP repairs, AP Fill 700, and AP Lift 475 fixed and lifted the slab.
Performance Data Point
Soil stabilized 28 feet deep, no excavation.
Documentation Reference
Ready when you are
Match the method to what's actually
failing below
Concrete leveling and stabilization restores elevation and stabilizes the ground beneath it, so the correction has something to hold onto. When the condition is recurring, unclear, traffic-sensitive, or tied to water, technical review helps you choose the right sequence the first time.