Leak Sealing & Water Control · Gel Injection Resin

Spetec GT380 Polyurethane Gel Injection Resin

A single-component hydrophilic resin that reacts with the water in a leaking joint and expands, curing as a rubbery foam or a stable gel that stays flexible while the structure keeps moving.

Hydrophilic

Foam or gel

Manhole rehabilitation

Curtain grouting

What it is

A hydrophilic resin that cures as a flexible foam or a stable gel

Spetec GT380 is a single-component, hydrophilic polyurethane gel injection resin used to shut off water leaks in concrete, brickwork, and sewers where the structure moves or settles. It reacts with the water already in the crack or joint and expands to fill the opening and seal the leak. The cured resin is highly flexible, which is what makes it hold up in joints that keep working after the repair.

GT380 injects single component, or two component in combination with water, and requires no catalyst. Soaked into oakum, an oil-free compressible fibrous packing, it also seals wider and irregular joints, which is the standard approach on precast manhole joints.

Where it is used

What GT380 is used for

GT380 is part of the Spetec Leak Seal Systems line and sits in the Leak Sealing & Water Control solution family.

  • Leaks in concrete, brickwork, and sewers where movement or settlement occurs

  • Precast manhole joint infiltration, with oakum soaked in GT380

  • Automatic sewer injection with packer systems

  • Foundation water cut-off: diaphragm walls, sheet piling, and secant piles

  • Water-carrying cracks and joints in tunnel segments

  • Curtain grouting behind tunnel, concrete, sewer walls, and sheet piling

  • Water cut-off membranes and liners in tunnels

  • Soil stabilization

How it works

How GT380 seals a joint that keeps moving

GT380 is injected into a wet crack or joint, where it reacts with the water present and expands to fill the opening and seal the leak. Depending on how it is mixed and injected, the cured resin forms either a rubbery foam, expanding 200 to 500 percent, or a stable gel, expanding 500 to 700 percent. Either outcome cures highly flexible, which is the property that suits GT380 to structures where settlement and movement continue after the crew leaves.

Gel time is short and temperature driven. At 77°F the published gel times run 37 to 48 seconds across the tested water ratios; at 40°F the same ratios run 1 minute 52 seconds to 2 minutes 22 seconds. Colder water slows the reaction, so injection is planned around the temperature of the structure rather than the air.

Technical specifications

Published properties


Physical properties

Property

Value

Method

Appearance, uncured

Clear amber liquid

-

Viscosity at 77°F (25°C)

315 cP (315 mPa·s)

ASTM D4878

Density at 77°F (25°C)

66.8 lb/ft³ (1.07 kg/dm³)

ASTM D3505

Expansion

Rubbery foam, 200 to 500%, or stable gel, 500 to 700%

Product page, not restated in the current TDS


Gel time by water ratio

Water ratio

At 77°F

At 40°F

1:1

48 seconds

2 minutes 22 seconds

1:5

37 seconds

1 minute 52 seconds

1:8

43 seconds

1 minute 56 seconds

Injection time

25 to 60 seconds

-


Handling & certification

Property

Value

Method / Note

Composition

Single component, hydrophilic; no catalyst required; injects single component, or two component in combination with water

TDS / product page

Application temperature

41–95°F (5–35°C)

TDS

Storage

50–80°F (10–26°C)

TDS

Shelf life

24 months, unopened, within storage range

TDS

Packaging

5-gallon pails and 10.5 oz INJECTR Series cartridges

Product page

Source: Spetec GT380 Technical Data Sheet, Rev. 7/30/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.

Downloads

Data sheets and application guides

Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.

Compatible equipment & accessories

What you need to inject GT380

  • Single-component airless injection pump, recommended for GT380. View pumps 

  • Crack-injection valves and packers, including the packer systems used for automatic sewer injection. View accessories 

  • INJECTR Series Cartridges, 10.5 oz cartridge format for small-volume and access-limited work. View cartridges 

  • Alchatek Pump Flush and Soak 130, reusable biodegradable pump flush for shutdown, and the solvent that cleans cured polyurethane off equipment. View flush  View solvent 

  • Oakum, oil-free compressible fibrous packing, forced into a joint or opening to provide a backing, seal, or carrier for the resin. It has to be oil free, because oiled fiber will not absorb the resin. View 

Related articles & guides

Learn the method behind the product

Frequently Asked Questions

Yes. GT380 is hydrophilic and water reactive. It reacts with the water already in the crack or joint and expands to fill the opening and seal the leak, so a leak running at the time of injection is the condition it is built for.

Either, depending on how it is mixed and injected. The product page publishes a rubbery foam that expands 200 to 500 percent, or a stable gel that expands 500 to 700 percent. Both cure highly flexible, which is what suits GT380 to structures that keep moving.

No. GT380 is a single-component resin and requires no catalyst. It can be injected single component, or two component in combination with water.

Concrete, brickwork, and sewers where movement or settlement occurs; precast manhole joints and inverts; foundation elements such as diaphragm walls, sheet piling, and secant piles; water-carrying cracks and joints in tunnel segments; curtain grouting behind walls and sheet piling; and water cut-off membranes and liners in tunnels.

Fast, and it depends on temperature. At 77 degrees F the published gel times run 37 to 48 seconds across the tested water ratios. At 40 degrees F the same ratios run 1 minute 52 seconds to 2 minutes 22 seconds. Published injection time at 77 degrees F is 25 to 60 seconds.

All three are flexible resins for cracks and joints that move. GT380 is a hydrophilic gel resin that cures as a rubbery foam or a stable gel and is the usual choice for manhole rehabilitation. GT350 is an MDI-based hydrophilic resin for wet, dynamic cracks and joints. F400 is a hydrophobic, closed-cell resin, and it is the one to reach for when the cured foam must not take water back up.

Yes, and it is the standard approach on precast manhole joints. Oakum is an oil-free compressible fibrous packing that is soaked in GT380 and packed into the joint. It has to be oil free, because oiled fiber will not absorb the resin. The soaked oakum holds the resin in place while it reacts with water and expands.

A single-component airless injection pump is recommended, along with crack-injection valves and packers, and a pump flush or cleaning solvent for shutdown. GT380 is also used in automatic sewer injection with packer systems, and is available in INJECTR Series cartridges for small-volume work.

5-gallon pails and 10.5 ounce INJECTR Series cartridges.

Unopened containers have a 24 month shelf life when stored between 50 and 80 degrees F.

No. They are the same product. Alchatek dropped PUR from the name, so older data sheets, labels, and purchase orders may still read Spetec PUR GT380. The resin itself did not change.

Proof & Verification

GT380-PB-01

Slot 1: Named Project / Case Study

empty, Alchatek to supply
Case Studies

GT380-PB-02

Slot 2: Performance Data Point or Credential

empty, Alchatek to supply
Case Studies

GT380-PB-03

Slot 3: Documentation Reference

empty, Alchatek to supply
Case Studies

Specifying GT380 for a manhole program, or weighing a gel against a foam resin? Talk the condition through before you commit to a method.

For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.