Leak Sealing & Water Control · Injection Resin
Spetec GT500 Polyurethane Injection Resin
A single-component hydrophilic resin thin enough to travel into a hairline crack, that cures into a closed-cell foam stretching to 350 percent before it breaks.
NSF/ANSI/CAN 61 & 372 Certified · Certified for contact with drinking water. The listing carries use restrictions.
Hydrophilic
Closed cell
Crack & joint injection
Oakum gaskets
On this page:
What it is
A thin, closed-cell hydrophilic resin for cracks that keep moving
Spetec GT500 is a single-component, hydrophilic polyurethane injection resin used to seal cracks, joints, and pipe penetrations in concrete by pressure injection. Its low viscosity, 215 cP, lets it travel into hairline cracks rather than stopping at the face. It reacts with the water present, expands about six times, and cures into a closed-cell foam that bonds tenaciously to wet concrete.
GT500 requires no catalyst and is phthalate free. It is also used to saturate dry oakum, an oil-free compressible fibrous packing, to build a flexible gasket for a pipe penetration, a joint, or a larger defect.
Where it is used
What GT500 is used for
GT500 is part of the Spetec Leak Seal Systems line and sits in the Leak Sealing & Water Control solution family.
Sealing cracks in concrete structures by pressure injection
Hairline cracks, wide cracks, and expansion joints
Pipe joints and pipe penetrations
Oakum gaskets: dry oakum saturated in GT500, for penetrations and larger defects
Structures in contact with drinking water, within the restrictions of the NSF listing
How it works
How GT500 gets into a crack too tight for a thicker resin
GT500 is injected under pressure into the crack, where it reacts with the water present, expands about six times, and cures into a flexible closed-cell foam that seals the crack. The reaction is staged and quick: an initial reaction at about 30 seconds, full rise at about 1.5 minutes, and full cure at 24 hours.
Two published properties do the work after that. The cured foam is closed cell and shrinks less than 2 percent, so it holds its volume in the crack instead of pulling away from the faces. Elongation at break is 350 percent, which is what lets the seal follow a crack that keeps opening and closing.
Technical specifications
Published properties
Physical properties, uncured
Property | Value | Method |
|---|---|---|
Appearance | Clear amber liquid | - |
Viscosity at 77°F | 215 cP (215 mPa·s) | ASTM D4878 |
Density at 77°F | 72.4 lb/ft³ | EN ISO 2811-1 |
Reaction & cured properties
Property | Value | Method |
|---|---|---|
Initial reaction | About 30 seconds | TDS |
Full rise | About 1.5 minutes | TDS |
Full cure | 24 hours | TDS |
Expansion | About 6x | TDS |
Tensile strength | 450 psi | ASTM D3574 |
Elongation at break | 350% | ASTM D3574 |
Tear resistance | 21 lb/in | ASTM D3574 |
Shrinkage | Less than 2% | ASTM D1042 / D756 |
Handling & certification
Property | Value | Method / Note |
|---|---|---|
Composition | Single component, hydrophilic, closed cell; no catalyst required; phthalate free | TDS / product page |
Application temperature | 41–95°F | TDS |
Storage | 50–80°F | TDS |
Shelf life | 24 months, unopened, within storage range | TDS |
Packaging | 5-gallon pail | Product page |
Certification | NSF/ANSI/CAN 61 and 372. Certified for contact with drinking water. The listing carries use restrictions on wetted surface area and minimum tank volume. See the certificate. | TDS Rev. 7/13/2026 and NSF certified product listing |
Source: Spetec GT500 Technical Data Sheet, Rev. 7/13/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.
Downloads
Data sheets and application guides
Technical Data Sheet (TDS)
Published properties · PDF
Safety Data Sheet (SDS)
Handling & safety · PDF
NSF/ANSI/CAN 61 & 372 Certificate
Certified product listing · PDF
Application Guide, Cracks & Joints
Standard injection procedure · PDF
Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.
Compatible equipment & accessories
What you need to inject GT500
Single-component airless injection pump, recommended for GT500. View pumps
High-pressure crack-injection valves and packers, for setting and injecting cracks, joints, and pipe penetrations. View accessories
Oakum, oil-free compressible fibrous packing, saturated in GT500 to build a flexible gasket for a penetration, a joint, or a larger defect. It has to be oil free, because oiled fiber will not absorb the resin. View
Alchatek Pump Flush and Soak 130, reusable biodegradable pump flush for shutdown, and the solvent that cleans cured polyurethane off equipment. View flush View solvent
Related articles & guides
Learn the method behind the product
Sealing Leaks - Crack Injection & Curtain Wall Grouting
Method explainer
Hydrophobic Polyurethanes vs Hydrophilic Polyurethanes
Chemistry comparison
Two Products Will Stop Most Water Leaks
Field walk-through
Frequently Asked Questions
Yes. GT500 is hydrophilic and water reactive. It is injected under pressure into the crack, reacts with the water present, expands, and cures into a flexible closed-cell foam that seals the crack. It also bonds tenaciously to wet concrete.
No. GT500 is a single-component resin and requires no catalyst.
Its published viscosity is 215 cP at 77 degrees F, which is low for an injection resin. A thin resin travels into a hairline crack instead of stopping at the face of it, so the seal forms through the depth of the crack rather than across the surface.
GT500 is certified to NSF/ANSI/CAN 61, which covers contact with drinking water, and to NSF/ANSI/CAN 372, which covers lead content. The listing carries use restrictions on wetted surface area and minimum tank volume, so read the certificate and confirm the certification is current before specifying.
About six times, per the published data. It expands as it reacts with water and cures into a closed-cell foam that shrinks less than 2 percent, so it holds its volume in the crack.
Yes. Published elongation at break is 350 percent by ASTM D3574, with tensile strength of 450 psi and tear resistance of 21 pounds per inch. That is what lets the seal follow a crack that keeps opening and closing.
The published sequence is an initial reaction at about 30 seconds, full rise at about 1.5 minutes, and full cure at 24 hours.
Cracks in concrete structures sealed by pressure injection, including hairline cracks, wide cracks, and expansion joints; pipe joints and pipe penetrations; and larger defects sealed with an oakum gasket saturated in the resin.
Yes, and it is one of the product's main uses. Oakum is an oil-free compressible fibrous packing. Dry oakum is saturated in GT500 and packed into the opening to build a flexible gasket for a pipe penetration, a joint, or a larger defect. It has to be oil free, because oiled fiber will not absorb the resin.
All three are flexible resins for cracks that move. GT500 is the thinnest of the three at 215 cP and cures closed cell with 350 percent elongation, which suits hairline cracks and oakum gaskets. GT350 is an MDI-based hydrophilic resin at 280 cP for wet, dynamic cracks and joints. F400 is hydrophobic, so its cured foam does not take water back up.
Unopened containers have a 24 month shelf life when stored between 50 and 80 degrees F.
No. They are the same product. Alchatek dropped PUR from the name, so older data sheets, labels, and purchase orders may still read Spetec PUR GT500. The resin itself did not change.
Proof & Verification
GT500-PB-01
Water Treatment Plant Losing Two Million Gallons Per Day Due to Leaks
Specifying GT500 for a hairline crack program, or deciding between a thin injection resin and an oakum gasket? Talk the condition through before you commit to a method.
For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.