Leak Sealing & Water Control · Injection Resin
Spetec HighFoamer Polyurethane Injection Resin
A single-component semi-rigid resin that expands up to 50 times and reacts in seconds, for cutting off high-flow water and filling the voids behind it.
NSF/ANSI/CAN 61 & 372 Certified · Certified for contact with drinking water. The listing carries use restrictions.
Hydrophobic
Semi- rigid
Gushing leaks
Curtain grouting
On this page:
What it is
A fast, high-expansion foam for gushing water and open voids
Spetec HighFoamer is a single-component, hydrophobic, closed-cell polyurethane injection resin that expands up to 50 times and cures semi-rigid, used to cut off high-flow water leaks and fill voids. Its data sheet describes it as a fast-reacting, high-foaming, semi-rigid resin for sealing gushing leaks and filling voids. That is a different job from the flexible resins in the line, which are built for cracks and joints that move.
HighFoamer is solvent free and phthalate free, and it is the one resin here that requires a catalyst. Alchatek Gen Cat or Gen Cat Fast must be added, both for proper foam formation and to set the reaction time to the job.
Where it is used
What HighFoamer is used for
HighFoamer is part of the Spetec Leak Seal Systems line and sits in the Leak Sealing & Water Control solution family.
Water cutoff of large-flow and high-pressure leaks
Curtain grouting behind walls and slabs
Foundation water cut-off: diaphragm walls, sheet piling, and secant piles
Crack, void, and gravel-layer stabilization
Mine, tunnel, pipe jacking, and tunnel boring work
Sewer and stormwater leak sealing, and manhole injection
Probe grouting for below-grade pipes
Soil stabilization and anchors
How it works
How HighFoamer shuts down water that is already gushing
HighFoamer is injected with catalyst into the flowing water, where it reacts in seconds, expands up to 50 times, and cures into a closed-cell semi-rigid foam that fills the opening and stops the flow. The expansion is what does the work: a small volume of resin becomes a large volume of foam, so it can fill a void or a gravel layer that would take far more of a low-expansion resin.
Speed is set by catalyst dosage and temperature, not by the resin alone. At 10 percent Gen Cat Fast the published reaction starts in 5 seconds at 41°F; at 5 percent Gen Cat it runs out to 95 seconds at 77°F. Cured tensile elongation is 3.80 percent, against hundreds of percent for the flexible resins, so HighFoamer is built to fill and hold, not to follow a crack that keeps moving.
Technical specifications
Published properties
Physical properties
Property | Value | Method |
|---|---|---|
Appearance, uncured | Brown liquid | - |
Viscosity at 77°F | 215 cP (215 mPa·s) | ASTM D4878 |
Density at 77°F | 69.9 lb/ft³ | EN ISO 2811-1 |
Expansion | Up to 50x | TDS |
Density, cured, free rise | 1.2 lb/ft³ | ASTM D3574 |
Compressive strength | Up to 1,803 psi | ASTM C-39 |
Tensile strength | 43 psi | ASTM D-1623 |
Tensile elongation | 3.80% | ASTM D-1623 |
Shrinkage | Negligible | ASTM D-1042 / D-756 |
Reaction time, start to end
Catalyst | Dosage | At 41°F | At 59°F | At 77°F |
|---|---|---|---|---|
Gen Cat Fast | 5% | 9 to 43 sec | 14 to 57 sec | 19 to 75 sec |
Gen Cat Fast | 8% | 7 to 30 sec | 10 to 35 sec | 15 to 40 sec |
Gen Cat Fast | 10% | 5 to 22 sec | 8 to 28 sec | 10 to 35 sec |
Gen Cat | 5% | 14 to 55 sec | 18 to 78 sec | 18 to 95 sec |
Gen Cat | 8% | 10 to 43 sec | 14 to 51 sec | 15 to 60 sec |
Gen Cat | 10% | 8 to 35 sec | 11 to 41 sec | 15 to 48 sec |
Handling & certification
Property | Value | Method / Note |
|---|---|---|
Composition | Single component plus required catalyst; hydrophobic, closed cell, semi-rigid; solvent free and phthalate free | TDS / product page |
Application temperature | 34–95°F (1–35°C) | TDS |
Storage | 50–80°F (10–26°C) | TDS |
Shelf life | 24 months, unopened, within storage range | TDS |
Packaging | 0.5 gallon and 5 gallon per the data sheet; the product page also lists cartridge formats | Product page |
Certification | NSF/ANSI/CAN 61 and 372. Certified for contact with drinking water. The listing carries use restrictions on wetted surface area and minimum tank volume. See the certificate. | TDS Rev. 7/30/2026 and NSF certified product listing |
Both catalysts are yellow-orange liquids at 65.5 lb/ft³ with a 313°F flash point; viscosity at 77°F is 75 cP for Gen Cat and 70 cP for Gen Cat Fast. Reaction times are start to end of reaction. Source: Spetec HighFoamer Technical Data Sheet, Rev. 7/30/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.
Downloads
Data sheets and certificates
Technical Data Sheet (TDS)
Published properties · PDF
Safety Data Sheet (SDS)
Handling & safety · PDF
NSF/ANSI/CAN 61 & 372 Certificate
Certified product listing · PDF
Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.
Compatible equipment & accessories
What you need to inject HighFoamer
Alchatek Gen Cat and Gen Cat Fast, required with HighFoamer, both for proper foam formation and to set reaction time. Do not order the resin without one. View catalysts
Single-component airless injection pump, recommended for HighFoamer. View pumps
Injection packers and valves, including the probe and packer setups used for curtain grouting and void injection. View accessories
Alchatek Pump Flush and Soak 130, reusable biodegradable pump flush for shutdown, and the solvent that cleans cured polyurethane off equipment. View flush View solvent
Related articles & guides
Learn the method behind the product
Sealing Leaks - Crack Injection & Curtain Wall Grouting
Method explainer
Hydrophobic Polyurethanes vs Hydrophilic Polyurethanes
Chemistry comparison
Control Gushing Leaks with Curtain Grouting
Field walk-through
Frequently Asked Questions
High-flow water and large voids. Its data sheet describes it as a fast-reacting, high-foaming, semi-rigid resin for sealing gushing leaks and filling voids. Reach for it when the problem is volume and pressure, not a hairline crack.
Up to 50 times, per the published data. That is far more than the flexible crack-injection resins in the line, which is why it is the one to use when a void has to be filled rather than a crack sealed.
Yes, and this is different from most of the line. The data sheet states that Gen Cat or Gen Cat Fast is required with HighFoamer for proper foam formation and to adjust set times. It is not optional, and dosage is how reaction time is controlled.
Very fast, and it is tunable. With Gen Cat Fast at 10 percent the published reaction starts in 5 seconds at 41 degrees F. With Gen Cat at 5 percent at 77 degrees F the reaction runs out to 95 seconds. Dosage and temperature set the working window.
No. HighFoamer is semi-rigid. Published tensile elongation is 3.80 percent, where the flexible resins in the line run in the hundreds of percent, and published compressive strength runs up to 1,803 psi. It is built to fill and hold, not to follow a crack that keeps moving.
HighFoamer is certified to NSF/ANSI/CAN 61, which covers contact with drinking water, and to NSF/ANSI/CAN 372, which covers lead content. The listing carries use restrictions on wetted surface area and minimum tank volume, so read the certificate and confirm the certification is current before specifying.
The published application range is 34 to 95 degrees F, which is colder than most of the Spetec Leak Seal line. Reaction slows as temperature drops, so catalyst dosage is set to the temperature on site.
Water cutoff of large-flow and high-pressure leaks; curtain grouting; foundation elements such as diaphragm walls, sheet piling, and secant piles; crack, void, and gravel-layer stabilization; mine, tunnel, pipe jacking, and tunnel boring work; sewer and stormwater sealing; probe grouting for below-grade pipes; and manhole injection.
A single-component airless injection pump is recommended, along with injection packers and valves, Alchatek Gen Cat or Gen Cat Fast, which are required, and a pump flush or cleaning solvent for shutdown.
By job, not by chemistry alone. HighFoamer and F400 are both hydrophobic, but HighFoamer is semi-rigid and expands up to 50 times, so it fills volume and cuts off high flow. F400 is flexible and stays flexible, for cracks and joints that move. GT500 is a thin hydrophilic resin for hairline cracks. Pick HighFoamer when the problem is a void or a gusher, and a flexible resin when the problem is a moving crack.
Unopened containers have a 24 month shelf life when stored between 50 and 80 degrees F.
No. They are the same product. Alchatek dropped PUR from the name, so older data sheets, labels, and purchase orders may still read Spetec PUR HighFoamer. The resin itself did not change.
Proof & Verification
HF-PB-01
Curtain Grouting in a Repurposed Power Plant Intake Well
Water already running, and not sure whether the answer is a high-expansion foam or a flexible resin? Get the call right before the packers go in.
For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.