Concrete Leveling & Soil Stabilization · Accessories
Slab Lifting Hoses, Injection Ports and Geotechnical Accessories
The heated hose, ports, fittings, filters, and consumables that a proportioner and gun run with, matched to the gun you carry and the work you do.
ISO 9001 Certified Manufacturer
One-Year Warranty on Alchatek-Made Parts and Materials
On this page:
In short
What runs with a proportioner and a slab lifting gun
Alchatek supplies the hose, ports, fittings, filter, positioning tool, and consumables that complete a slab lifting or deep soil injection setup: heated main hose and whip hoses, a hose wrap, five port and fitting types matched to specific guns, an A-side in-line filter, the Jack Attack System, and three consumables for flushing, cleaning, and surface protection. The proportioners, guns, and skid system themselves are on the Geotech Equipment page.
Two kinds of things live on this page, and they are covered by two different warranties: the hardware you install or connect, and the consumables you use up. The warranty section sets out which is which.
Choose your accessories
Match the accessory to the gun, the hose run, and the job
Two questions settle most of it: which gun you are running, because each gun takes its own port or fitting, and how far the hose has to reach from the rig to the work. The items below are grouped by what they do, and each one opens with the condition it fits.
Heated hose and whip hose
Two-component foam has to arrive at the gun at temperature, so the main line is heated. The whip hose is the short flexible section at the gun end. Hoses and hose assemblies are not manufactured by Alchatek and carry the manufacturer's warranty.
If you are running foam from the rig to the work and it has to arrive at temperature
50' Heated Hose
The heated main line, in 50 foot sections, rated 2000 to 3500 psi. Available as TC or non-TC, and with or without a scuff jacket for abrasion.
If your hose runs are losing heat or getting torn up on the ground
Sidewinder Hose Wrap
A wrap for the hose run that adds insulation and abrasion resistance. Insulated and non-insulated versions.
If you need a spare or backup whip for a MixMaster Pro or a pneumatic gun, and do not need it heated
6' Non-Heated Whip Hose
A non-heated whip assembly rated 3500 psi, with a third high-pressure line for the water or air supply a MixMaster Pro or pneumatic gun needs.
If you need a heated whip at the gun, or a heated spare
10' Heated Whip Hose
A heated whip assembly, 1/4 inch by 10 feet, rated 3500 psi, for backup or spare use.
Ports and fittings, by gun
Each gun takes its own port or fitting. Pick by the gun you are running. The Deep Lock® fittings are for Alchatek's deep soil injection stabilization system, where the resin goes down injection pipes rather than into a slab.
If you are running a MixMaster Pro
Tapered Ports
Tapered ports that seal between the MixMaster Pro gun and the concrete.
If you are running a PMC PX-7
Concave Ports with Sealing Sleeve
Concave ports with a sealing sleeve, for a reliable connection to the PX-7 slab lifting gun.
If you are running a low-pressure lifting system with a MiniMaster gun
Static Mixer & Tapered Port
A static mixer and tapered port set that mixes the two components thoroughly before injection on a low-pressure system.
If you are running Deep Lock® and need high-volume resin flow into the injection pipe
Button Head Fittings
Fittings engineered for high-volume resin flow with a smooth surface, for Deep Lock® deep soil injection.
If you are running Deep Lock® and need the mechanical connection to the injection pipe
Tubing Injection Assembly
The assembly that makes a reliable mechanical connection to the injection pipes in the Deep Lock® process.
Filters and positioning tools
What protects the gun, and what moves the slab.
If crystallized A-side material or debris is reaching the gun
A-Side In-Line Filter
An in-line filter on the A side that stops crystallization chunks, debris, and contaminants before they reach the slab lifting gun.
If you need to position a small or medium slab while you lift or stabilize it, with one operator
Jack Attack System
A leverage device for positioning small to medium slabs into place while lifting or stabilizing with polyurethane. Two triangular steel frames per system, manual operation, one person. Sidewalk slabs, driveways, golf cart paths, pool decks.
Flushes and surface protection
Consumables. These are chemical products and carry the Chemical Product Limited Warranty, not the equipment warranty.
If you are shutting down the pump at the end of the day
Alchatek Pump Flush
A high-performance, reusable, biodegradable flush for clearing injection pumps at shutdown.
If you need to protect finished surfaces from staining during injection
Alchatek Surface Guard 125
A stain preventer for finished surfaces near the injection work.
If resin has already cured on metal parts
Alchatek Soak 130
The solvent that cleans cured resin off metal components. For after the fact, where flush is for before.
Putting a first kit together? A first slab lifting kit is the proportioner and gun, a heated main hose to reach the work, a whip hose to the gun, the ports that match the gun, an A-side filter, and pump flush for shutdown. Technical Services can tell you what a complete setup needs for the work you are actually doing.
Sizes and specifications
Published sizes and specifications
Hose
Item | Length | Pressure rating | Options |
|---|---|---|---|
50' Heated Hose | 50 ft sections | 2000 to 3500 psi | TC or non-TC; with or without scuff jacket |
Sidewinder Hose Wrap | Per hose run | n/a | Insulated or non-insulated |
6' Non-Heated Whip Hose | Confirm, see note | 3500 psi | Third high-pressure line for water or air supply |
10' Heated Whip Hose | 1/4 in by 10 ft | 3500 psi | Heated |
Ports and fittings, by gun
Item | Fits | Job |
|---|---|---|
Tapered Ports | MixMaster Pro | Seal between gun and concrete |
Concave Ports with Sealing Sleeve | PMC PX-7 | Reliable gun connection |
Static Mixer & Tapered Port | MiniMaster, low-pressure systems | Mix before injection |
Button Head Fittings | Deep Lock® injection pipe | High-volume resin flow |
Tubing Injection Assembly | Deep Lock® injection pipe | Mechanical connection to the pipe |
Jack Attack System
Property | Value | Note |
|---|---|---|
Construction | Triangular steel frame | TDS Rev. 1/20/2026 |
Units per system | Two | TDS |
Operation | Manual, one operator | TDS |
Anchoring | Compatible with screw-in concrete anchors | TDS |
Typical slabs | Sidewalks, driveways, golf cart paths, pool decks | TDS |
Sources: live Slab Lifting Accessories page for hose, port, and fitting data; Jack Attack System TDS Rev. 1/20/2026. Hose and fitting rows carry no manufacturer specification because none is published.
Warranty
Which warranty covers what
Accessories fall under two different Alchatek warranties depending on what the item is. Hardware is covered by the Equipment and Rig Limited Warranty, Form 9301. Consumables such as flushes, solvents, lubricants, and additives are chemical products and are covered by the Chemical Product Limited Warranty, Form 9300. It is worth a minute before you buy, because the two work differently.
Hardware: packers, ports, valves, fittings, tools
Items Alchatek manufactures or fabricates are warranted for one year from the date of shipment under Form 9301. Hoses and hose assemblies are not manufactured by Alchatek and carry no Alchatek warranty of any kind; the sole warranty is the manufacturer's, on the manufacturer's terms. Coverage is for the original purchaser only.
Read the Equipment and Rig Limited Warranty →
Consumables: flushes, solvents, lubricants, additives
Chemical products are warranted to be free from manufacturer's defects and to meet the published properties on their current data sheet for one year, when used according to published instructions and within shelf life. Storage conditions matter: keep them within the range printed on the data sheet.
Documentation
Data sheets
Jack Attack System, Data Sheet
Slab positioning tool · PDF
Soak 130, Safety Data Sheet
Handling and safety · PDF
Soak 130, Technical Data Sheet
Published properties · PDF
Pump Flush, Technical Data Sheet
Published properties · PDF
Pump Flush, Safety Data Sheet
Handling and safety · PDF
Surface Guard 125, Technical Data Sheet
Published properties · PDF
Surface Guard 125, Safety Data Sheet
Handling and safety · PDF
Assembling a submittal package or comparing products? Every data sheet, specification, and certificate lives in the central Downloads library.
The equipment
What these accessories run with
Geotech Equipment, the proportioners, guns, and skid system that the hoses, ports, and fittings on this page connect to.
Leak Seal Accessories, the packers, ports, and consumables for crack injection rather than slab lifting.
Training and startup
Getting the setup right the first time
Most slab lifting problems on site trace back to the accessories, not the machine: foam arriving cold because the hose run outgrew the heat, a port that does not match the gun, or A-side crystals reaching the gun because there was no filter. All of that is teachable before the first job.
Training & Education
For training a crew on the injection work itself
Technical Services
For kit questions, sizing, and setup on a specific job
Contractor Tools
For the estimators and selectors that shape a job before it is scoped
Frequently Asked Questions
Each gun takes its own. Tapered ports fit the MixMaster Pro. Concave ports with a sealing sleeve fit the PMC PX-7. The static mixer and tapered port set is for a low-pressure system running a MiniMaster. For Deep Lock, Alchatek's deep soil injection stabilization system, the resin goes down injection pipes rather than into a slab, and the button head fittings and the tubing injection assembly are the connections for that.
Where they sit in the run. The 50 foot heated hose is the main line from the proportioner toward the work, rated 2000 to 3500 psi, and it is heated so the two components arrive at temperature. The whip hose is the short flexible section at the gun end, available non-heated at 6 feet with a third supply line for the gun's water or air, or heated at 10 feet. Both whips are rated 3500 psi.
Because two-component foam has to be at temperature when it reaches the gun, and a long run across cold ground pulls heat out of it. Keeping the A and B preheaters and the hose heater working is the biggest factor in pumping in cold weather, and the Sidewinder wrap adds insulation on top of the heated hose for long or exposed runs.
It stops crystallization chunks, debris, and contaminants in the A-side line before they reach the slab lifting gun. A-side material can crystallize, and a chunk that reaches the gun blocks or damages it, so the filter sits in the line ahead of the gun.
A leverage device for positioning small to medium slabs while you lift or stabilize them with polyurethane. Two triangular steel frames per system, operated manually by one person, compatible with screw-in concrete anchors. It is for sidewalk slabs, driveways, golf cart paths, and pool decks.
Insulation and abrasion resistance on the hose run. It comes insulated or non-insulated. Use the insulated version when heat loss along the run is the problem, and either version when the hose is being dragged over concrete and gravel.
Use Alchatek Pump Flush at shutdown; it is a reusable, biodegradable flush for clearing the pump before foam can cure in it. Use Alchatek Surface Guard 125 on finished surfaces near the injection work to prevent staining. If resin has already cured on metal parts, Alchatek Soak 130 is the solvent that removes it.
Hoses and hose assemblies do not. They are not manufactured by Alchatek, and the sole warranty is the manufacturer's, on the manufacturer's terms. Hardware that Alchatek manufactures or fabricates is covered for one year from shipment by the Equipment and Rig Limited Warranty. Consumables such as flush, solvent, and surface protection are chemical products covered by the Chemical Product Limited Warranty for one year within shelf life.
The gun decides the port, the hose run decides the heat, and the job decides the rest. Send us the condition and we will tell you what the kit actually needs.
For sizes and specifications, see the data above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.