Market · Transportation

Lift, stabilize, and seal transportation infrastructure: from settled roads and bridge approaches to leaking tunnels.

Transportation assets fail in two directions: the ground beneath them moves, and water gets in where it shouldn't. Settlement, voids, and washout show up as cracked approaches, rough pavement, and dropping slabs, while groundwater shows up as leaking highway, transit, rail, and pedestrian tunnels, culverts, and buried structures. Polyurethane injection lifts and stabilizes settled surfaces in place, Deep Lock® deep injection reaches weak soil at depth, and leak-sealing injection stops active water at the source, often without full reconstruction.

Roads & bridge approaches

Tunnels & culverts

Embankments & shoulders

Lift, stabilize & seal in place

Bigger than the visible symptom

A rough approach, a dropping slab, or a leaking tunnel is usually a sign of something behind the surface.

The bump at the end of a bridge, a settled lane, a void opening under a runway apron, a tunnel wall that weeps after every rain: the surface defect is the symptom drivers and inspectors notice. What is usually behind it: weak or consolidating embankment fill, washed-out soil, a void where support used to be, or water under pressure finding its way through the joints, cracks, and segment gaps of tunnels, culverts, and buried structures.

Settled bridge approach slab creating a bump where asphalt meets the concrete deck

The two often feed each other: water moving behind a tunnel wall or beneath pavement carries soil away, and the lost soil becomes the void that lets the surface drop. Reaching the real cause, not just the surface defect or the stain, is what separates a repair that holds from one that returns at the next inspection cycle.

Where this applies

If it carries traffic and it has settled, lost support, or is leaking, it usually belongs here.

These are the transportation conditions seen most often, led by the higher-consequence ones. Start with what you are seeing in the field and follow it into the matching condition or repair page.

Technician working on a concrete-lined drainage slope along a highway, with a support truck parked on the shoulder

Not sure which condition you are dealing with?

Describe what you are seeing on the asset, a settling approach, a voided apron, or a leaking tunnel, and get a defensible repair direction before the project moves further or a closure is scheduled.

Stronger early decisions reduce disruption

Routed correctly early, most transportation conditions can be repaired in place: with less closure and less repeat work.

Polyurethane injection is targeted and cures quickly, so a lane, ramp, approach, apron, or tunnel section can often be repaired in a short window and returned to service the same day, no large excavation, no extended staging. When movement or a leak is caught early, the ground beneath an approach can be stabilized, and the water in a tunnel or structure stopped, before the condition spreads into adjacent spans, joints, or shoulders.

The cost of waiting

Left active, settlement, washout, and leaks tend to widen. An approach that could be lifted today, or a tunnel joint that could be sealed before it erodes the soil behind it, can become a recurring closure, a rideability complaint, and eventually a reconstruction, a far larger, more disruptive, and more public project than acting early.

The snapshot below is a quick way to tell where a given condition should go next.

Where the condition is

Typical next step

Decision trigger

Settled road or approach, or active water in a tunnel/structure

Bridge Approach Settlement · Water Intrusion & Water Entry

The issue needs a narrower diagnosis before a method is chosen

Repair direction already forming, lift, stabilize, or seal

Concrete Leveling and Stabilization · Soil Stabilization · Leak Sealing

The main question is method fit and application

Issue reaches below the surface, embankment, deep fill, or subgrade

Deep Foundation & Sitework

The cause is not limited to the slab or pavement surface

Traffic-critical or higher-consequence asset

Technical Services

Delay or the wrong method carries larger operational and public risk

When the condition runs deeper than it looks

Lifting the surface is the right move: until the cause is in the soil below it or the water behind it.

When the only problem is a void right under the slab, filling it and lifting the surface is the whole repair. But transportation conditions often start deeper, in weak embankment fill, washed-out subgrade, or water moving through a tunnel wall, and a surface lift alone will settle again. Matching the repair to the actual cause is what keeps the asset in service.

Cross-section of a bridge approach showing void filling, slab lift and Deep Lock injection into weak embankment fill
Technician injecting grout into a leaking crack in a concrete wall of a roadway underpass with an injection gun and hoses

From here the path runs into the repair method, then onward to the specific materials and systems that fit the asset:

Working a wider municipal program, or an issue that sits below the visible surface? Those route on to Public Works and Deep Foundation & Sitework.

Transportation: common questions

On the settlement side: roads, pavements, bridge approaches and approach slabs, embankments, rail trackbed, transit slabs, and airport aprons and taxiways. On the water side: tunnels, culverts, and buried utility structures. Wherever a surface has settled or lost support, or water is leaking into a structure, polyurethane injection can usually lift, stabilize, or seal it in place. A project review confirms the fit.

The work is done from inside the structure with no excavation, so lanes, tracks, or sections can usually stay in service or reopen quickly. Leak-sealing injection grout is placed into the cracks, joints, and segment gaps where water is entering; it fills the path and stops the flow at the source. Tunnel size, water volume, and access determine the sequence, scoped in a project review.

Groundwater under pressure finds the weakest path in: construction joints, cracks, cold joints, and gaps between tunnel segments or pipe sections. That flow can also wash out the soil behind the wall, which is why a leak is sometimes the first sign of a developing void. Sealing the leak and addressing any soil loss behind it together keeps the repair from returning.

Often, yes. When an approach slab is intact but has dropped, polyurethane injection fills the void beneath it, lifts it back toward grade, and stabilizes the soil under it, fixing the bump without tearing out and repouring the slab. If the approach embankment itself is weak, the repair has to reach deeper, which is where soil stabilization comes in.

Usually because the patch only corrects the surface while the cause stays active below. Approach settlement is typically driven by weak or consolidating embankment fill and voids that open beneath the approach slab. Filling the void and stabilizing the ground beneath the approach addresses the cause, so the transition is far less likely to drop again. A repair that skips the soil tends to buy time, not a fix.

Yes. High-density polyurethane is engineered to carry structural loads and is widely used beneath load-bearing transportation slabs and pavements. It fills the void, re-supports the slab, and stabilizes the soil so the surface returns to grade and stays in service. Because load and tolerance requirements vary by asset, the system and density are matched to the specific application during a project review.

Often both, and that is where the methods work together. Water moving through an embankment, beneath pavement, or into a tunnel erodes soil and opens voids, which shows up as settlement above. The repair may pair leak sealing with soil stabilization so the water is stopped at the source and the weakened ground is strengthened, not just the visible surface corrected.

In most cases the work is far less disruptive than reconstruction. Polyurethane injection is targeted, requires no large excavation, and cures quickly, so a lane, ramp, apron, or tunnel section can often reopen the same day. Closure time depends on the size of the area and site access, which a project review scopes before work begins.

This page validates transportation asset and environment fit, roads, bridges, approaches, embankments, rail, transit, and tunnels, and routes you into the matching condition and repair method. The Public Works page covers municipal infrastructure such as water and wastewater treatment and public facilities. If your question is about a transportation asset and the condition affecting it, you are in the right place.

When the condition is recurring, traffic- or runway-critical, hard to define, or carries higher public consequence if the wrong method is chosen. A repeat repair history, active water in a tunnel or structure, deep or unusual soils, and tight load tolerances are all signals to bring in technical review before a method is selected, so the work begins from a clear condition definition.

Proof & Verification

Named Project

DOT Culvert Void Fill

Voids under precast box culvert slabs on a major Utah roadway were filled with AP Lift 440 in about 3 hours, with minimal traffic disruption.
Case Study

Performance Data Point

All voids filled in about three hours.

Documentation Reference

Transportation assets rarely fail at the surface alone, but caught early, most settled roads and approaches can be lifted and stabilized, and most leaking tunnels and structures sealed, in place and with far less closure than reconstruction. Tell us what is happening on the asset and get a defensible repair plan.