Solution · Soil Stabilization & Settlement Control
Soil Stabilization and Settlement Control for Weak, Variable, or Unstable Soils
Improve bearing, reduce settlement risk, and match the repair method to the actual soil behavior before visible movement is treated like a surface-only problem.
NSF/ANSI 61 certified options for potable water contact
ISO 9001 certified manufacturing
Soil tested before treatment
In short
What is soil stabilization?
Soil stabilization improves how weak or unreliable soils behave within a defined treatment zone (the area of weak soil the injected resin reaches and improves), reducing settlement risk and recurring movement. It corrects what’s failing below grade, not just the surface symptom above it. Alchatek delivers this with Deep Lock®, its structural polyurethane injection system for stabilizing weak soils below grade.
Diagnosis Before Method™
The difference between a repair that lasts and one that fails.
Diagnosis
Identify the visible symptom
Understand what changed below
Then select the method
Match the method to what failed below
Confirm the correction holds
Project fit
Project Fit Snapshot
Stabilization can hold, because the weak soil is the real problem.
Weak, variable, or unstable soils are driving recurring movement
Surface correction alone has not held, or will not, because the ground beneath cannot carry it
Keep reading. Deep Lock® improves how those soils behave within the treatment zone.
Something else must be corrected with it, or first.
The slab elevation also has to come back up
Add Concrete Leveling and Stabilization, in sequence.
Active water, seepage, or washout is still degrading the treatment zone
The condition runs deeper than the treatment zone, or needs load transfer
Technical Services for project-specific review.
How the method works
How soil stabilization works
Soil stabilization improves how weak or unreliable soils behave within a defined treatment zone (the area of weak soil the injected resin reaches and improves), reducing settlement risk and recurring movement. Alchatek delivers this with Deep Lock®, its structural polyurethane injection system for stabilizing weak soils below grade.
Step 01
Test the soil column
An Alchatek Pagani DPM-30 dynamic cone penetrometer (DCP) records continuous soil resistance layer by layer, establishing where the weak zone begins and ends before any material is injected.
How deep to test depends on the project. On most residential work there is rarely a need to test below about fifteen feet, and where firm soil is found by ten feet, that is often deep enough to stop. Deeper testing is warranted when conditions suggest the problem extends further down.
Step 02
Define the treatment zone
The treatment zone is the volume of weak soil the injected resin is intended to reach and improve. Its depth and extent come directly from the DCP results rather than from assumption, which is why the testing comes first.
Step 03
Match the material to the soil
Single-component polyurethanes are permeation grouts. In permeable soils such as sand, the resin travels through the pore space between soil particles and binds the soil matrix in place. Two-component polyurethanes are used where soil is not permeable (clay, for example), where the resin cannot travel through pore space and instead works by displacing and densifying the surrounding soil.
A note on terminology, because the industry is loose with it: two-component work is often called compaction grouting, lens grouting, or soil improvement grouting. Compaction grouting has a specific technical definition that polyurethane injection does not meet, but the term persists in common use. What matters for method selection is the soil’s permeability, not the label.
Step 04
Inject at depth
Injection depth follows what the DCP recorded. Spacing depends on the material: three to five feet for two-component, and one to three feet for permeation grouting with single-component. Excavation assist can call for two to three staggered rows of pipes rather than a single line.
Treatment works from the bottom of the weak zone upward. That is achieved either by driving pipes to several depths at one location and injecting through each, or by driving a single pipe to the deepest point and raising it as injection proceeds. The second approach is faster and more technical. Which one fits depends on the site and the crew.
Step 05
Cure
Polyurethane cures quickly, commonly reaching roughly 90 percent of its strength within about fifteen minutes and ready for service in about thirty, depending on conditions and the scope of the work.
Step 06
Confirm improvement where the project calls for it
On most residential and commercial work there is no formal post-treatment verification step. Where confirmation is warranted, a plate compaction test is the most direct way to demonstrate that bearing has improved.
Because stabilization improves the treatment zone rather than the surface above it, the correction addresses the reason movement started.
Paired methods
Paired methods, and when stabilization isn’t enough on its own
Not every problem belongs in a stabilization-first answer. Some conditions are mainly shallow contact loss and need controlled lift; others have active water routes that keep degrading the ground until water-control logic is part of the sequence. In those cases stabilization is paired with another method:
If the slab elevation also has to come back up
Concrete Leveling and Stabilization
When grade or slab elevation must be restored after the treatment zone is improved.
If water is still moving through the ground
Leak Sealing & Water Control
When seepage, leakage, or pressure-driven water is still degrading the ground beneath.
If the work sits in an excavation, shaft, or launch pit
Deep Foundation & Sitework
When excavation, launch-pit, shaft, or deeper below-grade risk shapes the question.
If the problem runs deeper than soil improvement can reach
Technical Services
When the condition extends beyond what soil improvement can address on its own.
Repeat risk
Why treating this as a surface problem creates repeat risk
When deeper or broader instability below grade is treated like a shallow surface issue, the result is often repeat movement, recurring repair, and a method that appears to work until the ground beneath keeps changing.
Water still active
When water is still driving the problem
If seepage, washout, or active water entry is still degrading the ground, stabilization should be paired with water-control logic, or reviewed first.
FAQ
The method
It is the improvement of how weak soils behave within a defined treatment zone so settlement risk, weak-soil behavior, or unreliable bearing can be reduced.
It is the right fit when weak, variable, degrading, or poorly performing soils are the main reason bearing is unreliable.
No. Soil stabilization improves how weak or unreliable soils behave within the treatment zone. Concrete leveling and stabilization restores slab elevation and re-supports the near-surface ground beneath it, a different method for a different problem. Some projects need both, in sequence.
Yes. Some projects require a combined sequence where support improvement and elevation correction both matter.
Fit and limits
It may not be enough when active water routes are still driving the condition, when isolated shallow contact loss is the main issue, or when a different structural support approach is more appropriate.
When the method matches what’s failing below and is executed correctly, it can significantly reduce recurrence risk.
If the main issue is broader ground instability, stabilization is more likely. If the main issue is loss of contact or shallow cavity formation, the repair path may begin with void-related logic instead.
When to escalate
Bring in water-control logic when seepage, leakage, washout, migration, or pressure-driven water movement are still actively weakening the treatment zone.
Bring in Technical Services when the ground problem is deeper, recurring, higher consequence, unusual, or difficult to narrow from the page alone.
Navigate
Navigate from here
Start with the condition you can see
Methods that pair with stabilization
Soil Instability Beneath Structures
If the ground under the structure keeps moving or no longer feels reliable
Settled Concrete Slabs
If a slab has dropped below the elevation it started at
Voids Beneath Concrete
If there is an open gap or cavity under the concrete
Soil Erosion & Washout
If water is carrying soil out from under the structure
Bridge Approach Settlement
If the approach or transition slab at a bridge has dropped
Water Intrusion & Water Entry
If water is visibly getting into the structure
Concrete Leveling and Stabilization
If the slab elevation also has to be corrected once the ground beneath is improved
Leak Sealing & Water Control
If water is still moving through or into the structure
Deep Foundation & Sitework
If the work sits in an excavation, shaft, launch pit, or other below-grade context
Engineering and documentation
When to bring in a person
Engineering Resources
If you need specification-level detail before deciding
Downloads
If you need the files: TDS, SDS, specifications, NSF certificates, case studies
Knowledge Center
If you are still learning how these methods differ
Technical Services
If the condition is deeper, recurring, or higher-consequence than this page can narrow
Request Project Assistance
If you have a specific project and want the method matched to it
Training & Education
If your crew needs to be trained on the injection work itself
Proof & Verification
Named Project
CVS Pharmacy Soil Stabilization
Performance Data Point
Construction schedule held, no excavation required.
Documentation Reference
Ready when you are
The soil is the real problem. Treat it that way.
Match the method to the actual soil behavior, and bring in project-specific review before movement is treated like a surface-only fix.