Concrete Leveling & Stabilization · Void Fill Foam

AP Fill 420 High-Expansion Polyurethane Foam

A 2 lb foam that expands up to 35 times its liquid volume, the highest in the range. Built to fill large voids, abandoned pipes, and mine shafts with the least material.

ISO 9001 Certified · Facility-wide quality management certification.

Void Filling

Abandoned Pipes & Mine Shafts

Flotation Foam

Wet Conditions

What it is

A fill foam, built for volume rather than load

AP Fill 420 is a two component, high-expansion, hydro-insensitive polyurethane foam used to fill voids, abandoned pipes and mine shafts, and to serve as flotation foam. It is a 2 lb foam that expands up to 35 times its liquid volume. That expansion is the reason to specify it. A large void takes a large amount of material, and a foam that yields 35 cubic feet from one cubic foot of liquid fills that space for a fraction of what a heavier grade would cost.

This is a void filling foam, not a slab lifting foam

AP Fill 420 is the lightest grade in this range at 22 psi free-rise compressive strength, and its data sheet does not list slab lifting among its uses. To raise a settled slab, start with AP Lift 430, a 3 lb structural foam at 50 psi. Use AP Fill 420 when the job is filling space, not carrying a structure.

It is hydro insensitive, which means water does not stop the reaction, and the product page states that the foam displaces water as it expands. The two sides are heated, metered, and mixed at the gun.

Where it is used

What AP Fill 420 is used for

AP Fill 420 sits in the Concrete Leveling and Stabilization solution family, where it does the filling and stabilizing work rather than the lifting. The data sheet lists these uses:

  • Filling abandoned pipes, mine shafts, and similar

  • Filling voids

  • Flotation foam

If the concrete above the void has also dropped and needs to come back to grade, start with settled concrete slabs. If the void is a symptom of ground washing out from underneath, start with voids beneath concrete or soil erosion and washout, because filling a void that is still being eroded only buys time.

How it works

Why 35 times expansion is the whole economic case

The two components are heated and mixed at the gun and injected into the void, where the foam expands rapidly, displaces water, fills the available space, and cures into a closed-cell mass that bonds to soil and concrete. Reaction is slower than the lifting grades, creaming in 5 seconds and reaching full rise at 38, which gives the foam time to travel and find the far corners of a void rather than building a plug at the injection point.

Expansion and density pull against each other across this range, and AP Fill 420 sits at the far end of that tradeoff. It expands 35 times where a 3 lb lifting grade expands 25 and the 6 lb grade expands 12. You get roughly three times the filled volume per gallon compared with the heaviest grade, and in exchange you get a foam that fills and supports its own mass rather than one that jacks concrete.

Strength still develops quickly. The data sheet publishes 90 percent of full strength in about 15 minutes.

Technical specifications

Published properties


Cured foam, free rise

Property

Value

Method

Density, free rise

2 lb foam. Nominal 2 lb/ft³, range 1.75 to 2.25 lb/ft³ (28 to 36 kg/m³)

ASTM D1621

Compressive strength, free rise

22 psi, or 3,170 psf (152 kPa)

ASTM D1621 / D1622

Shear strength, free rise

11 psi, or 1,580 psf (76 kPa)

ASTM C273

Flexural strength

50 psi, or 7,200 psf (345 kPa)

ASTM D790

Shrinkage

Negligible

ASTM D1042 / D756

Expansion, unconfined

Up to 35 times liquid volume

TDS

Strength development

90% of full strength in about 15 minutes

TDS


Cured foam, confined

Property

1.5x

2x

3x

Compressive strength, confined

40 psi, 5,760 psf

60 psi, 8,640 psf

98 psi, 14,100 psf

Shear strength, confined

20 psi, 2,880 psf

30 psi, 4,320 psf

49 psi, 7,060 psf

Confined values are what the foam does once it is compacted inside a closed void rather than rising freely, which is why they run above the free-rise figures. The data sheet labels these levels 1.5x, 2x and 3x without stating what the multiplier is measured against, so confirm the basis with Technical Services before using them in a submittal.

Reaction profile at 105°F

Stage

Time

Method

Cream time

5 seconds

ASTM D7487

Tack-free time

36 seconds

ASTM D7487

Rise time

38 seconds

ASTM D7487

Liquid components

Property

A side

B side

Specific gravity

1.23

1.02

Weight per gallon

10.25 lb

8.5 lb

Viscosity at 110°F

200 cP (200 mPa·s), ASTM D4878

Handling and storage

Property

Value

Method / Note

Composition

Two component high-expansion polyurethane foam, heated and mixed at the gun

TDS

Storage temperature

50 to 80°F (10 to 26°C)

TDS

Equipment settings

Not published for this product. Confirm with Technical Services before running

Absent from the TDS

Packaging

100-gallon and 500-gallon units, each a matched A-side and B-side pair

Product page

AP Fill 420 is a 2 lb foam, the lightest grade in this range, and it is a void filling product rather than a slab lifting one. Density is how these foams are graded, and the range above is the manufacturing tolerance on that grade, not a choice. Free-rise values are unconfined laboratory figures; confined inside a void the foam reaches a higher density and higher strength, which is what the confined table shows. This data sheet publishes no tensile strength, no mix ratio, no closed cell percentage, no water absorption, no equipment temperature settings and no shelf life in months, and none of those has been carried across from another product's data sheet. Source: AP Fill 420 Technical Data Sheet, Rev. 1/20/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.

Downloads

Data sheets

Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library. For a specification naming AP Fill 420, contact Technical Services.

Compatible equipment & accessories

What you need to install AP Fill 420

  • Two-component proportioner with material heaters, required. AP Fill 420 cannot be poured or hand mixed. View proportioners

  • MixMaster Pro gun, named on the product page. View gun

  • PX-7 gun, the alternate gun option. View gun

  • Alchatek Surface Guard 125, protects finished surfaces during injection. View accessory

  • Alchatek Pump Flush, reusable, biodegradable pump flush for shutdown. View flush

  • Alchatek Soak 130, cured-polyurethane cleaning solvent. View solvent

Related articles & guides

Learn the method behind the product

Frequently Asked Questions

Filling voids, filling abandoned pipes and mine shafts, and as flotation foam. It is a void filling foam. It fills space and displaces water at very low material cost per cubic foot, and it is not intended to raise a settled slab.

No. AP Fill 420 is a 2 lb foam at 22 psi free-rise compressive strength, the lightest and weakest grade Alchatek publishes in this range, and its data sheet does not list slab lifting among its uses. Lifting a settled slab calls for one of the AP Lift grades, which start at 3 lb and 50 psi. If the job is filling a void rather than raising concrete, AP Fill 420 is the efficient choice.

The technical data sheet publishes an unconfined expansion of 35 times its liquid volume, the highest of any grade in this range. That is the whole point of the product: a large void is filled with far less material than a heavier lifting grade would need. Unconfined is a laboratory free-rise figure, so real expansion in a confined space is lower and the resulting density is higher.

It is a 2 lb foam. Published free-rise values are 22 psi compressive strength, or 3,170 psf, and 11 psi shear strength, or 1,580 psf, at a nominal cured density of 2 pounds per cubic foot. Flexural strength is 50 psi. Confined in a void the foam reaches a higher density and higher strength than these free-rise figures, and the data sheet publishes confined values at three levels of confinement.

They are compressive and shear values measured at three levels of confinement, labelled 1.5x, 2x and 3x on the data sheet, running from 40 psi compressive at 1.5x up to 98 psi at 3x. The data sheet does not define what the multiplier is measured against, so confirm the basis with Technical Services before using these values in a submittal.

It is hydro insensitive, which means water does not stop the reaction, and the product page states that it displaces water as it expands. Confirm the approach for your specific conditions with Technical Services, particularly where the void is fully flooded or connected to flowing water.

Yes. Filling abandoned pipes and mine shafts is the first use listed on the data sheet. The high expansion is what makes it practical: a long run of abandoned pipe is a large volume to fill, and a 35 times expansion foam fills it with far less material than a heavier grade. Note that this product carries no drinking water certification, so it is not suitable for potable water applications.

A two-component proportioner with material heaters, plus a MixMaster Pro or PX-7 gun. This is not a product that can be poured or hand mixed. The two sides are heated, metered, and mixed at the gun.

The AP Fill 420 data sheet does not publish equipment temperature settings, unlike the AP Lift data sheets. It publishes viscosity measured at 110 degrees F and reaction times measured at 105 degrees F, but those are test conditions rather than machine settings. Confirm equipment settings with Technical Services before running the product.

The data sheet gives a storage range of 50 to 80 degrees F but does not publish a shelf life in months, unlike the AP Lift sheets which publish 24 months. Confirm shelf life with Alchatek before ordering, and keep both sides sealed and within the storage range.

No. AP Fill 420 carries no NSF certification. Its data sheet makes no certification claim and no certificate is published for it. Where a job requires contact with drinking water, use a product that carries a current certificate and read that certificate for the conditions of its listing.

100-gallon and 500-gallon units. Each unit is a matched pair of A-side and B-side containers.

Proof & Verification

APFILL420-PB-01

Slot 1: Named Project / Case Study

Project name · asset class & location · condition addressed · method & system family · documented outcome · documentation reference (Downloads).
Case Studies

APFILL420-PB-02

Slot 2: Performance Data Point / Credential

Claim · supporting evidence · source · date.
Case Studies

APFILL420-PB-03

Slot 3: Documentation Reference

Link to the full case study / formal file in Downloads. Leave empty until the real reference exists.
Case Studies

Large void, abandoned pipe, or a shaft that has to be filled and taken off the books? Talk the volume and the grade through before the material is ordered.

For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.