Joint & Crack Sealants · Silicone Sealant
Alchatek SlabSeal 142 Silicone Joint Sealant
An ultra-low modulus silicone with 1000 percent elongation at break, for cracks and joints in concrete that never stop moving.
Moving joints
Ultra-low modulus
Unprimed adhesion
20 oz sausage
On this page:
What it is
A silicone built to move with the joint, not fight it
Alchatek SlabSeal 142 is a single-component, neutral cure, ultra-low modulus silicone caulk sealant for cracks and dynamically moving joints in concrete. It cures on the moisture in the air, bonds to concrete and steel without a primer on clean dry surfaces, and stretches to 1000 percent elongation before it breaks.
Low modulus is the property that matters. At 150 percent stretch the sealant is still only pulling back at 42 psi, so it follows the joint instead of tearing itself off the edge or pulling the concrete apart with it.
Where it is used
What SlabSeal 142 is used for
SlabSeal 142 sits in the Joint & Crack Sealants family. A joint sealant closes the face of a crack or joint at the surface. It does not fill the crack through the structure, which is what an injection resin does.
Sealing cracks in concrete
Sealing dynamically moving joints
Finishing concrete slabs after lifting and leveling
Joints exposed to UV, weather and wide temperature swings
Water still coming through the joint? Seal it first and finish it after. A sealant laid over an active leak can be pushed straight off the joint. Start at Leak Sealing and Water Control.
How it works
How an ultra-low modulus silicone survives a joint that keeps working
SlabSeal 142 is gunned into the joint over a backer rod, tooled, and left to cure on the moisture in the air, forming a rubber band across the joint that stretches and recovers as the slab expands and contracts. The published joint movement capability is plus 100 percent and 50 percent by ASTM C719.
The backer rod is not optional on a moving joint. It stops the sealant bonding to the bottom of the joint, so the sealant is anchored on two faces instead of three and is free to stretch across the gap. Fill a moving joint solid and the sealant is liable to tear the first cold night.
Technical specifications
Published properties
Cured sealant
Property | Value | Method |
|---|---|---|
Durometer hardness | 20 Shore A | ASTM D2240 |
Tensile strength | 150 psi (10.5 kg/cm²) | ASTM D412 |
Stress at 150% elongation | 42 psi (3.0 kg/cm²) | ASTM D412 |
Elongation at break | 1000% | ASTM D412 |
Joint movement capability | Plus 100% and 50% | ASTM C719 |
Accelerated weathering | No degradation | ASTM C793 |
Uncured sealant & cure
Property | Value | Method / Note |
|---|---|---|
Specific gravity | 1.13 | TDS |
Extrusion rate | 100 g/min | 3.2 mm (1/8 in) orifice at 90 psi |
Slump or sag | Nil | TDS |
Cure system | Neutral oxime, moisture cure | TDS |
Cure time | 7 days | TDS |
Handling & limitations
Property | Value | Method / Note |
|---|---|---|
Composition | Single component, neutral cure, ultra-low modulus, 100 percent silicone | TDS and product page |
Adhesion | Unprimed to concrete, steel and most construction substrates, on clean dry surfaces free of dust and frost | Product page |
Joint preparation | Closed-cell or bi-cellular backer rod on moving joints; do not fill the joint solid; remove existing sealant completely | TDS |
Not suitable for | Active water leaks, submerged or continuous immersion, painting or coating over. May stain porous substrates such as natural stone, marble, granite and some architectural concrete; test first | TDS |
Storage | 50–80°F (10–26°C) | TDS |
Packaging | 20 oz sausage | Product page; not published on the TDS |
Shelf life, application temperature range and color options are not published on the current data sheet; ask Technical Services. Source: Alchatek SlabSeal 142 Technical Data Sheet, Rev. 9/10/2026, except where the Note column says otherwise. Properties vary with site conditions; confirm against the current data sheet before specifying.
Downloads
Data sheets
Technical Data Sheet (TDS)
Published properties · PDF
Safety Data Sheet (SDS)
Handling and safety · PDF
Assembling a submittal package or comparing products? Every TDS, SDS, spec, and certificate lives in the central Downloads library.
Compatible equipment & accessories
What you need to apply SlabSeal 142
Bulk or sausage gun, sized for the 20 oz sausage. Supplied by the crew.
Closed-cell or bi-cellular backer rod, required on moving joints so the sealant bonds on two faces and is free to stretch.
Joint preparation tools, for removing existing sealant completely and leaving the substrate clean, dry and sound. Supplied by the crew.
Related articles & guides
Learn the method behind the product
Concrete Joint Sealant vs. Concrete Joint Filler
Product selection
Announcing AP SlabSeal 142
Product introduction
Polyurethane Slab Lifting Explained
Method explainer
Frequently Asked Questions
Sealing cracks and dynamically moving joints in concrete, and finishing slabs after they have been lifted and leveled. It closes the joint at the surface once the structural work is done.
Where the material goes. An injection resin is pumped into the crack or joint and fills it through the full depth of the structure. A joint sealant like SlabSeal 142 closes only the face of the joint at the surface. If water is coming through, the resin is the repair and the sealant is the finish.
The data sheet publishes a joint movement capability of plus 100 percent and 50 percent by ASTM C719, with 1000 percent elongation at break by ASTM D412. It is an ultra-low modulus silicone, which is what lets it follow a joint that keeps working instead of tearing away from the edge.
The data sheet publishes a 7 day cure at standard conditions. It is a neutral oxime moisture cure, so it draws the moisture it needs from the air rather than from a second component.
20 Shore A by ASTM D2240. Tensile strength is 150 psi by ASTM D412, and the stress at 150 percent elongation is 42 psi. Low stress at high stretch is the point: the sealant gives rather than pulling the joint edge apart.
No. The data sheet states it is not paintable or coatable. Silicones do not accept coatings. If the joint has to be painted, a silicone is the wrong chemistry for that joint.
Not on most substrates. It is published as giving unprimed adhesion to concrete, steel and most construction substrates, provided the surface is clean, dry, and free of dust and frost. Do not apply it over a damp, frosted, contaminated or unsound substrate, and remove any existing sealant completely first.
Yes on a moving joint. Use a closed-cell or bi-cellular backer rod and do not fill the joint solid. A sealant bonded on three sides cannot stretch, so it tears instead of moving.
No. The data sheet excludes active water leaks and continuous immersion. A leaking crack or joint is injection work, and the sealant goes on afterward as the surface finish.
20 oz sausages. Confirm the current size and color list with Technical Services before ordering, because the data sheet does not publish packaging.
Proof & Verification
SLABSEAL142-PB-02
Slot 2: Performance Data Point or Credential
Joint opening and closing with the seasons, or a slab just put back to grade? Get the joint detail right before the first sausage goes in.
For documentation, see the data sheets above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.