Leak Sealing & Water Control · Accessories
Crack Injection Packers, Ports and Leak Seal Accessories
The packers, ports, valves, oakum, and consumables that a leak seal injection pump runs with, so you can size the kit to the crack and the resin before the job.
ISO 9001 Certified Manufacturer
One-Year Warranty on Alchatek-Made Parts and Materials
On this page:
In short
What runs with a leak seal injection pump
Alchatek supplies fourteen accessories for polyurethane crack injection and leak sealing: three sizes of mechanical packer, two 3/8 inch injection ports, a crack injection valve, a twin-stream F-valve, a flush wand, oakum, and five consumables for flushing, cleaning, protecting, and reinforcing. The SealMaster injection gun is equipment and lives on the Leak Seal Equipment page.
Two kinds of things live on this page, and they are covered by two different warranties: the hardware you install or connect, and the consumables you use up. The warranty section sets out which is which.
Choose your accessories
Match the accessory to the crack, the concrete, and the resin
Three questions settle most of it: how wide the crack or joint is, whether the concrete is sound enough to hold a driven port or needs a packer that seals mechanically, and whether the resin is polyurethane or acrylic. The items below are grouped by what they do, and each one opens with the condition it fits.
Mechanical packers
A packer is set into a drilled hole and tightened to seal against the concrete, so resin can be injected under pressure. Match the packer to the hole you drill.
If you are injecting under pressure into sound concrete and drilling a 5/8 inch hole
5/8" Mechanical Packer
The largest of the three mechanical packers, for the largest drilled hole and the highest resin volume per port.
If you are drilling a 1/2 inch hole
1/2" Mechanical Packer
The mid-size mechanical packer, for a 1/2 inch drilled hole.
If you are drilling a 13 millimeter hole, or working to a metric specification
13mm Mechanical Packer
The metric mechanical packer, for a 13 millimeter drilled hole.
Injection ports
A port is driven into the drilled hole rather than tightened. Faster to set than a packer, and the choice for new or stable concrete.
If you want a driven port with a grease-gun style fitting for the injection connection
3/8" Hammer In Port with Zerk Fitting
A 3/8 inch port that is hammered into the drilled hole, with a zerk fitting for the injection connection.
If you are injecting chemical grout into new or stable concrete and want the lowest-cost port
3/8" Plastic Drive In Port
A 3/8 inch plastic port that is driven into the drilled hole. For injection of chemical grouts into new or stable concrete.
Valves and tools
What sits between the pump and the port, and what prepares the hole.
If you need to control resin flow at the point of injection, or turn an airless sprayer into an injection pump
High Pressure Crack Injection Valve
Controls resin flow at the point of injection. On an airless sprayer, it is the valve that turns the unit into an injection pump.
If you are twin-streaming, injecting resin and water at the same time
High Pressure F-Valve Assembly
Two supply connections feed resin and water into one stream before the coupler, for the twin-stream technique used with water-reactive resins.
If you have drilled the holes and need the dust out before you set packers
Flush Wand
Flushes concrete dust out of drilled holes before packers or ports go in, so the seal is against clean concrete.
Sealing material
For anything wider than a hairline, the resin needs something to hold it in place while it reacts.
If the crack, joint, or penetration is too wide for the resin alone to stay put, or water is gushing
Alchatek Oakum
Oakum is an oil-free compressible fibrous packing, forced into a joint or opening to provide a backing, seal, or carrier for another sealing material. Used dry as a temporary seal that slows gushing water and gives injected resin time to cure, or soaked in a water-reactive resin and packed into the joint. It has to be oil free, because oiled fiber will not absorb the resin. Sold in 5 pound and 25 pound boxes of 8 foot pieces, 1 1/4 inches in diameter.
Flushes, cleaners, and additives
Consumables. These are chemical products and carry the Chemical Product Limited Warranty, not the equipment warranty.
If you are shutting down the pump at the end of the day
Alchatek Pump Flush
A high-performance, reusable, biodegradable flush for clearing injection pumps at shutdown.
If resin has already cured on metal parts
Alchatek Soak 130
The solvent that cleans cured resin off metal components. For after the fact, where flush is for before.
If you are injecting a Spetec AG series acrylic gel and want a tougher cured gel
Alchatek Gel Reinforcing Agent
An acrylic latex additive for the AG series acrylic gels, used in soil stabilization and leak sealing of below-grade structures. About 50 percent solids, pH about 8.5, viscosity about 100 to 350 cps.
If you need to protect finished surfaces from staining during injection
Alchatek Surface Guard 125
A stain preventer for finished surfaces near the injection work.
If you are lubricating injection equipment
Alchatek Lube 190
Equipment lubricant for injection hardware.
Putting a first kit together? A first crack injection kit is a pump, packers or ports sized to the holes you will drill, a crack injection valve, oakum for anything wider than a hairline, and pump flush for shutdown. Technical Services can tell you what a complete setup needs for the work you are actually doing.
Sizes and specifications
Published sizes and specifications
Mechanical packers and injection ports
Item | Size | Type | Concrete |
|---|---|---|---|
5/8" Mechanical Packer | 5/8 in drilled hole | Mechanical, tightened to seal | Sound concrete, pressure injection |
1/2" Mechanical Packer | 1/2 in drilled hole | Mechanical, tightened to seal | Sound concrete, pressure injection |
13mm Mechanical Packer | 13 mm drilled hole | Mechanical, tightened to seal | Sound concrete, pressure injection |
3/8" Hammer In Port with Zerk Fitting | 3/8 in | Driven, zerk fitting | As published |
3/8" Plastic Drive In Port | 3/8 in | Driven, plastic | New or stable concrete |
Alchatek Oakum
Package | Contents | Piece length | Diameter |
|---|---|---|---|
5 lb box | 24 pieces | 8 ft | 1 1/4 in |
25 lb box | 120 pieces | 8 ft | 1 1/4 in |
Alchatek Gel Reinforcing Agent
Property | Value | Note |
|---|---|---|
Type | Acrylic latex additive for AG series acrylic gels | TDS Rev. 1/19/2026 |
Solids content | About 50 percent | TDS |
pH | About 8.5 | TDS |
Viscosity at 73.4°F | About 100 to 350 cps | Brookfield RV, spindle 1, 20 rpm |
Storage | 50 to 80°F (10 to 26°C) | TDS |
Sources: Alchatek Oakum TDS Rev. 1/19/2026; Alchatek Gel Reinforcing Agent TDS Rev. 1/19/2026; live Leak Seal Accessories page for packer and port sizes. The packer and port rows carry no manufacturer specification because none is published.
Warranty
Which warranty covers what
Accessories fall under two different Alchatek warranties depending on what the item is. Hardware is covered by the Equipment and Rig Limited Warranty, Form 9301. Consumables such as flushes, solvents, lubricants, and additives are chemical products and are covered by the Chemical Product Limited Warranty, Form 9300. It is worth a minute before you buy, because the two work differently.
Hardware: packers, ports, valves, fittings, tools
Items Alchatek manufactures or fabricates are warranted for one year from the date of shipment under Form 9301. Hoses and hose assemblies are not manufactured by Alchatek and carry no Alchatek warranty of any kind; the sole warranty is the manufacturer's, on the manufacturer's terms. Coverage is for the original purchaser only.
Read the Equipment and Rig Limited Warranty →
Consumables: flushes, solvents, lubricants, additives
Chemical products are warranted to be free from manufacturer's defects and to meet the published properties on their current data sheet for one year, when used according to published instructions and within shelf life. Storage conditions matter: keep them within the range printed on the data sheet.
Documentation
Data sheets
Alchatek Oakum, Data Sheet
Packaging and uses · PDF
Gel Reinforcing Agent, Data Sheet
Published properties · PDF
Gel Reinforcing Agent, Safety Data Sheet
Handling and safety · PDF
Soak 130, Technical Data Sheet
Published properties · PDF
Soak 130, Safety Data Sheet
Handling and safety · PDF
Lube 190, Technical Data Sheet
Published properties · PDF
Lube 190, Safety Data Sheet
Handling and safety · PDF
Pump Flush, Technical Data Sheet
Published properties · PDF
Pump Flush, Safety Data Sheet
Handling and safety · PDF
Surface Guard 125, Technical Data Sheet
Published properties · PDF
Surface Guard 125, Safety Data Sheet
Handling and safety · PDF
Assembling a submittal package or comparing products? Every data sheet, specification, and certificate lives in the central Downloads library.
The equipment
What these accessories run with
Leak Seal Equipment, the injection pumps and the SealMaster injection gun that the packers, ports, and valves on this page connect to.
Geotechnical Accessories, the hoses, ports, and consumables for slab lifting and deep soil injection rather than crack injection.
Training and startup
Getting the setup right the first time
Most leak seal problems on site are setup problems: a packer that does not match the hole, a port driven into concrete that will not hold it, dust left in the hole, or resin injected into a joint too wide to hold it without oakum. All of that is teachable before the first job.
Training & Education
For training a crew on the injection work itself
Technical Services
For kit questions, sizing, and setup on a specific job
Contractor Tools
For the estimators and selectors that shape a job before it is scoped
Frequently Asked Questions
Match the packer to the hole you drill. Alchatek supplies mechanical packers for 5/8 inch, 1/2 inch, and 13 millimeter holes. The packer has to seal against the drilled hole under injection pressure, so the size is not a preference, it is set by the bit. If the specification does not name a size, Technical Services will help you choose one for the crack and the resin.
How they hold in the hole. A mechanical packer is set in the drilled hole and tightened so it seals against the concrete, which suits pressure injection into sound concrete. A hammer-in or drive-in port is driven into the hole instead, which is faster to set. The plastic drive-in port is specified for injecting chemical grouts into new or stable concrete.
Oakum is an oil-free compressible fibrous packing, forced into a joint or opening to provide a backing, seal, or carrier for another sealing material. It has to be oil free, because oiled fiber will not absorb the resin. Soaked in a water-reactive resin and packed into a wide joint, it holds the resin in place while the resin reacts with water and expands to seal the joint.
Yes, as a temporary measure. Dry oakum packed into a crack or joint slows gushing water and gives injected resin time to cure. For the permanent seal, the oakum is soaked in a water-reactive resin, or the resin is injected behind the dry oakum once the flow is slowed.
Two box sizes, one piece size. A 5 pound box holds 24 pieces and a 25 pound box holds 120 pieces. Every piece is 8 feet long and 1 1/4 inches in diameter.
It is an acrylic latex additive for the Spetec AG series acrylic gels, used in soil stabilization and leak sealing of below-grade structures. It is about 50 percent solids with a pH of about 8.5. It is for acrylic gels, not for polyurethane resins.
Twin-streaming. The assembly has two supply connections, so resin and water are fed in and combined into one stream before the coupler. That is the technique for injecting a water-reactive resin together with the water it reacts with.
Use Alchatek Pump Flush at shutdown. It is a reusable, biodegradable flush for clearing the pump before resin can cure in it. If resin has already cured on metal parts, Alchatek Soak 130 is the solvent that removes it.
Yes, under two different documents. Hardware that Alchatek manufactures or fabricates is covered for one year from shipment by the Equipment and Rig Limited Warranty; hoses and hose assemblies carry no Alchatek warranty. Consumables such as flush, solvent, lubricant, and the Gel Reinforcing Agent are chemical products covered by the Chemical Product Limited Warranty for one year within shelf life.
The crack decides the packer, the joint decides whether you need oakum, and the resin decides the rest. Send us the condition and we will tell you what the kit actually needs.
For sizes and specifications, see the data above or reach Technical Services. To purchase, find an authorized distributor or a qualified contractor.