Back to Case Studies

Water Treatment Clearwell Leak Repair Chattanooga

Before and after: clearwell joint injection
Alchatek
Case StudyLeak Seal
clearwell Chattanooga, Tennessee

Water Treatment Plant Losing
Two Million Gallons Per Day Due to Leaks

lost to leaks
2million gallons per day
Product
Spetec GT500
Download as PDF
I · The Problem
Case Study  ·  01
01

What made this job
difficult.

clearwell
Chattanooga, Tennessee

On top of a hill northeast of Chattanooga, Tennessee sits a clearwell that belongs to Eastside Utilities. Built in the 1940's on a former Army post, this clearwell consists of twin 2-million gallon tanks used for treating surface water to turn it into drinking water. The problem was that less than half of the water coming into the clearwells was making it out the other side. Although this water treatment plant has undergone several upgrades in its 70+ year lifespan, the ground beneath it has been subject to settling and consolidation. The tanks had shifted slightly and in doing so, loosened some of the joints and the water stops contained within. A short drive downhill from the property revealed various gullies and small creeks created by water running down the hillside.

Key Condition
Twin 2-million gallon clearwell tanks had shifted due to settling and consolidation of the ground beneath them, loosening joints and water stops around the perimeter walls and roof support columns.
The Constraint
1,700gallons per minute
leak rate measured
well over 2-million gallons per day
II · The Solution
Case Study  ·  02
02

What was specified,
and how it went in.

Spetec GT500

An Alchatek certified installer was called in to utilize Spetec GT500, an NSF / ANSI 61 approved product for contact with drinking water, to seal the leaks. This single component polyurethane resin is designed to penetrate and seal off leaks in cracks, joints, and pipe penetrations. As a hydrophilic polyurethane, it chases down water and gets into the microstructure of the concrete, forming a flexible seal and a tenacious bond with the wet concrete.

The Material
Spetec GT500
Spetec GT500
Single component, hydrophilic polyurethane resin; NSF / ANSI 61 approved for contact with drinking water.
The Method
01
Identify
All of the joints around the perimeter walls were suspect as well as the roof support columns throughout each clearwell that penetrated through the floor.
02
Drill
The contractor drilled holes to intersect the leaking joints around the perimeter of the clearwell and along all interior joints.
03
Install
Injection ports were installed.
04
Inject
Spetec GT500 was pumped into each port to create an injected membrane within the joints and beneath the clearwell.
Safe for Drinking Water
Spetec GT500 is NSF / ANSI 61 approved for contact with drinking water.
As a hydrophilic polyurethane, it chases down water and gets into the microstructure of the concrete, forming a flexible seal and a tenacious bond with the wet concrete.
Less Than Half
Less than half of the water coming into the clearwells was making it out the other side.
III · The Proof
Case Study  ·  03
03

What the result was,
and what confirmed it.

remaining leak rate

After three days of injection the work was done and the site was cleaned up. Monitoring after the Spetec GT500 was installed indicated that the leak had been reduced from 1,700 gallons per minute to 10 gallons per minute. The small number of remaining leaks were attributed to the many vintage valves and fittings that are still present at the plant.

remaining leak rate
10gallons per minute
Reduced from 1,700 gallons per minute to 10 gallons per minute after three days of injection.
At a Glance
450p.s.i.
Tensile Strength
ASTM D-3574
350%
Tensile Elongation
ASTM D-3574
Less than 2%
Shrinkage
ASTM D-1042/D-756
300 - 330Centipoise
Same Day Viscosity at 25° C (77° F)
What Remains
The few remaining leaks were attributed to the many vintage valves and fittings still present at the plant.
Start the Conversation
Send us the job.
We will send back an approach.

Send us the soil report or the failure photos and Technical Services will return a written approach within two business days.

Alchatek manufactures polyurethane resins, chemical grouts, and injection equipment for infrastructure repair: leak sealing, soil stabilization, concrete lifting, and seawall repair. Headquarters in Tucker, Georgia, with a bonded warehouse in Reno, Nevada.