Start with a repair method
Infrastructure Repair Solutions: Four Methods, Matched to the Condition
Every Alchatek repair comes down to one of four methods. Each solution page explains how the method works, when it fits, when it does not, and which products and specifications go with it. Alchatek manufactures and supplies geotechnical and waterproofing materials and equipment. Installation is performed by trained contractors.
4 Repair Methods
Seal · Stabilize · Lift
ISO 9001 Certified Manufacturing
Trenchless · Minimal Excavation
In short
What repair methods does Alchatek offer?
Four. Concrete Leveling and Stabilization lifts a settled slab and stabilizes the ground beneath it. Soil Stabilization & Settlement Control strengthens weak or moving soil. Leak Sealing & Water Control stops active water entry. Seawall & Waterfront Stabilization restores eroded soil behind seawalls and bulkheads without excavation.
Choose your method
Four methods. Each card says, in plain terms, when it is the right one.
Two of the four contain the word stabilization, and that is where most people hesitate. The deciding question is whether the ground below is still solid or whether the ground itself is the problem.
Concrete Leveling & Stabilization
Choose this when a slab, pavement, or approach has dropped and the ground below is still basically solid. Lifts the concrete back to grade and stabilizes the ground beneath it so the correction holds. More than lifting: the cause underneath is addressed.
Soil Stabilization & Settlement Control
Choose this when the ground itself is weak, washed out, or still moving, usually under a structure, not just a slab. Strengthens the soil in a defined treatment zone so settlement is controlled at its source. Often paired with leveling afterward.
Leak Sealing & Water Control
Choose this when water is entering through a crack, joint, penetration, or wall below grade. Fills the crack or joint and seals the leak, with the system matched to the pressure and movement at the entry point.
Seawall & Waterfront Stabilization
Choose this when soil is escaping from behind a seawall, bulkhead, or dock apron. Fills voids and stabilizes the soil behind the wall from the land side, in saturated conditions, with no excavation and the structure in service.
Start with the condition instead
Not sure which method? Start with what you can see.
Each condition page diagnoses what is failing first, then routes to the method that fits. That order is the whole discipline: diagnosis before method.
Settled Concrete Slabs
A slab has dropped or tilted. Usually routes to Concrete Leveling and Stabilization.
Voids Beneath Concrete
A hidden gap under the slab. Usually routes to Concrete Leveling and Stabilization.
Soil Instability Beneath Structures
The ground itself is unreliable. Routes to Soil Stabilization & Settlement Control.
Bridge Approach Settlement
The bump at the bridge. Routes to leveling, soil stabilization, or both.
Soil Erosion & Washout
Water is moving the soil. Routes to soil stabilization or water control, depending on the mechanism.
Seawall Soil Erosion
Soil loss behind a wall. Routes to Seawall & Waterfront Stabilization.
Water Intrusion & Water Entry
Water is coming in. Routes to Leak Sealing & Water Control.
All conditions
The full list of conditions Alchatek's systems address, with plain-language cues for each.
Solutions: Common Questions
Ask what the ground below is doing. If a slab has dropped but the ground under it is still basically solid, Concrete Leveling and Stabilization lifts the slab and stabilizes the ground directly beneath it. If the ground itself is weak, washed out, or still moving, especially under a building or structure, Soil Stabilization & Settlement Control strengthens the soil first. Some projects need both, in that order.
Yes. A leaking joint can wash out the soil under a slab, so the leak is sealed and the slab is leveled. A seawall can lose soil while the deck behind it settles. The solution pages say when pairing is likely, and a project review confirms the sequence for a specific site.
Most of it is trenchless. The materials are injected through small ports or probes rather than open-cut trenches, so many projects involve little or no excavation and the facility, roadway, or waterfront stays in use. Whether a specific site qualifies depends on the conditions, which a project review confirms.
Alchatek manufactures and supplies geotechnical and waterproofing materials and equipment. Installation is performed by trained contractors. Each solution page explains the method so owners and engineers can evaluate it; contractors install it. If you need the work done, request project assistance and Alchatek can help connect you with a trained contractor.
In Engineering Resources, which holds CSI-format specifications, technical data sheets, safety data sheets, and details for each method, with a downloads section. Each solution page also links to the documents that apply to it.
Systems & Products groups every Alchatek product by the method it serves, so you match the condition first and the product second. The solution pages link to the products built for that method, and the equipment pages cover the pumps and accessories they run through.
Choose your method above, or skip ahead: tell us what is failing on your site and get the method matched to the condition.