Back to Case Studies

Deep Soil Stabilization House North Carolina

Project photo: Deep Soil Stabilization with Polyurethane
Alchatek
Case StudyDeep Soil Stabilization
two-story residential house North Carolina

Deep Soil Stabilization
with Polyurethane

A two-story residential house in North Carolina, built on poorly compacted fill dirt, began settling after 20 years. A contractor used deep soil polyurethane injection to stop the sinking and reinforce the soil.

Injection Points Installed
18tubes
Product
AP Lift 440
Download as PDF
I · The Problem
Case Study  ·  01
01

What made this job
difficult.

two-story residential house
North Carolina

A two-story residential house in North Carolina was built on poorly compacted fill dirt. After about 20 years, it began showing evidence of settling. Interior cracks appeared in the sheetrock and some of the floors were no longer level, indicating that the footings were slowly sinking. These symptoms of unstable soil were caused by about 1 inch of settling. The engineer on the project determined that the problem was not severe enough to require helical piers. A contractor was called in to stop the sinking and reinforce the soil via deep soil polyurethane injection.

The Constraint
1in
Settling
Signs of Settlement
01
Sheetrock cracks
Interior cracks appeared in the sheetrock.
02
Out-of-level floors
Some of the floors were no longer level.
03
Sinking footings
About 1 inch of settling on poorly compacted fill dirt.
II · The Solution
Case Study  ·  02
02

What was specified,
and how it went in.

AP Lift 440
DEEP LOCK®

An Alchatek tech consultant worked with the contractor to draw up a plan, indicating exactly where the injection points would be located. The engineer reviewed the plan for feasibility.

The Material
AP Lift 440
AP LIFT 440
Compressive Strength (ASTM D-1621): 80 p.s.i. or 11,520 p.s.f. Tensile Strength (ASTM D-638): 88 p.s.i. Expansion (Unconfined): 17-19 times. Density (ASTM-D 1622): 3.75 to 4.25 lb/ft3. Shrinkage (ASTM D-1042/D-756): Negligible.
The Method
01
Planned
An Alchatek tech consultant worked with the contractor to draw up a plan indicating exactly where the injection points would be located; the engineer reviewed the plan for feasibility.
02
Installed
The contractor installed 18 injection tubes to a depth of 7 feet.
03
Injected exterior
Foam was injected from outside the house, beneath the exterior footings.
04
Injected interior
Foam was injected from inside the house, beneath the load bearing interior walls.
Why Not Helical Piers
The engineer determined the problem was not severe enough to require helical piers.
Instead, a contractor was called in to stop the sinking and reinforce the soil with deep soil polyurethane injection.
III · The Proof
Case Study  ·  03
03

What the result was,
and what confirmed it.

Lift per Injection Sequence

The deep soil stabilization process densified the soil and stopped the settlement. In addition, the contractors achieved a half inch lift from the exterior injections and another half inch lift from the interior injection sequence. The customer was extremely happy with the results. The engineer was impressed as well and said he would recommend this procedure in similar future scenarios.

Lift per Injection Sequence
0.5in
half inch lift from exterior injections and half inch lift from interior injections
At a Glance
18tubes
Injection Tubes
installed to a depth of 7 feet
50lbs
Foam per Tube
split between 7 feet and 3.5 feet below grade
5ft
Spacing
approximate spacing between injection points
The engineer said he would recommend this procedure in similar future scenarios.
Project engineer
The Customer
The customer was extremely happy with the results.
Start the Conversation
Send us the job.
We will send back an approach.

Send us the soil report or the failure photos and Technical Services will return a written approach within two business days.

Alchatek manufactures polyurethane resins, chemical grouts, and injection equipment for infrastructure repair: leak sealing, soil stabilization, concrete lifting, and seawall repair. Headquarters in Tucker, Georgia, with a bonded warehouse in Reno, Nevada.